Loading ...
Loading ...
Loading ...
CAW
Am
CLEAN~G
(continued)
Drawer Removal
Drawers will stop
before
coming
all the way out of the refrigerator to
help prevent contents from spilling
onto
the
floor,
Drawers can easily
be
rcmoved
by tilting up slightly and pulling past the “stop” location.
To remove drawers when the refrigerator door cannot be opened
all the way:
1. Remove food
from
the drawer and its cover. If your refrigerator has
adjustable shelves, remove
food
from the bottom shelf and
temporarily relocate it
higber
up in cabinet.
2. Remove the flexible gasket at the
rear of tbe top drawer. Lift each
:1
end straight up until the slots on
the gasket are free of the drawer
support
tabs.
*
“
-
‘,.
,,,;,,
,/,
,
r“
‘----=--
*
/l/Ajj/l’l!
--——
————_-.. .–
3. Pull the drawer partway out. Reach
in, push the rear of the glass up; at
the same time,
pusb
it back until it
clears front-corner retainers.
4. Tilt
and
remove the cover.
5. Pull the drawer forward, lift the
front
to
clear stops, and remove tbe
drawer.
If the refrigerator door
doesn’t open completely, pull the
drawer out until it hits the
door.
Then lift the drawer up until it is
higher
than
the drawer supports, tilt
it and take it out.
6.
If tape holds the Convertible Meat
Drawer (on some models) cover to
the
drawer supports, remove the
ta~e.
Pull drawer
partway
out. Reach
‘m
.JQ,YI
jli,,
in:
push the rear
if
tbe
g~ass
up and,
at
the same time, back, until it clears
front-corner retainers,
7. Tilt
tirrd
remove the cover.
Avoid cleaning the cold glass cover
with hot water because the extreme
temperature difference may cause it
to break.
8.
Tilt and remove the drawer.
After cleaning, replace in reverse
order. When replacing the drawer
make sure
you
slide it through both
drawer
guides
on the
left
side.
When drawers and covers are back in
place,
reinstall gasket at the rear of the
top drawer. Fit the end of the plastic
drawer support into the slot on the
Easket,
with the rubber gasket tlap
facing
you. Make sure the gasket
snaps into place.
e
‘~:
~~
--”
‘~:,/~~
z>,,,
,’/,’////
,1
-.—-.=
=—=.
Light Bulb Replacement
Fresh Food Compartment-Upper Light
1. Unplug refrigerator.
—
2.
To align the control knob
Grooved
properly, note position of
~:~~~lde
numbered control for proper
reassembly, turn control to
OFF
and
pull off knob.
3.
PLdl
bottom of
li&ht
panel
down about
1/4
inch
(6
mm)
‘m
Pin
retainer,
‘&:
,%
*Q
%:&
-.
~~
.1
-
,,,
just enough to disengage lip at
rear from grooves in retainers
\!
7,
on rear wall.
4. Lift panel to disengage top from pins on side walls and
remove panel.
After replacing with same size bulb, reinstall panel (hang top on pins;
pull bottom down, push it back and release it to let lip
engage
grooves
in retainers). Replace temperature control knob in OFF position, turn
it to previous setting and plug refrigerator back
in.
Fresh Food Compartment-Lower Light (on some models)
This light is located behind a shield at the rear of tbe fresh food
compartment
1.
Unplug the refrigerator.
2. Grasp the top edge of the shield and lift it up and forward to free its
top
edge.
3. After replacing with the same size bulb, hook the top of the
shield
back in place.
Freezer Compartment
1.
Unplug the refrigerator.
2. Remove the shelf just below light shield. (The shelf
will be easier to remove if it is emptied first. )
3. Pull the light shield
toward
you to reach the bulb.
After replacing with same size bulb, reinstall shelf and plug the
refrigerator back in.
12
Loading ...
Loading ...
Loading ...