Loading ...
Loading ...
Loading ...
1-worktop
2
1
3
4
5
2-screw
3-bracket
4-hob
5-hob seal
Recommended installation
Wood block
Scraper for cleaning the hob
.
S
Worktop
Fixing bracket
Screw
Symbol
Product Information
Value Unit
Model Identification
Type of
Number of cooking zones
Heating Technology (cooking
areas, radiant cooking zones,
solid plates)
Diameter of useful surface area
per electric heated cooking zone
(rounded to the nearest 5mm)
Energy consumption cooking
zone area calculated per kg
Energy consumption calculated
per kg
Hob
Ø
--
--
--
--
EC
EC
Built-in ceramic hob
5
MM
Wh/kg
Wh/kg
Radiant cooking zones
190
Big ring: 194
Small ring: 187
Big ring: 180mm
Small ring: 145mm
Multiple zones:
Outer ring: 180mm,
Inner ring: 120mm
Multiple zones: 195
CACC95
Screws need to
removed
WARMING
Close the cable clamp after making the electrical connection.
Close the terminal board cover by twisting it down.
Cleaning
Turn off the main power to the hob before carrying out any maintenance and wait for it to cool down.
Use lukewarm water and detergents to clean enameled elements. Never use abrasive products. Clean
tough stains using non-abrasive detergents or warm vinegar.
Use sponges or a damp cloth to clean the hob. Remove cleaning liquid from the glass worktop with a damp
cloth and dry using a soft cloth. Note: excess water can damage the electric elements.
Clean the electric tops using a damp cloth, then lightly oil the top when it is still warm.
Only licensed repairers should service and repair the appliance
Installation
Electrical connection
Appliances with three-pole cable are set up for operation with alternating current at the voltage and
frequency indicated on the rating plate. Look at the connection wiring diagram. The earth conductor is
yellow/green.
The connection to the electricity supply must be made by a qualified person and following the regulations.
When the appliance is to be installed above a built-in oven, the two appliances must be connected
separately to make it easier to take the appliances out and for electrical safety.
The supply cable must be so positioned that no point can reach a temperature 50° C higher than ambient
temperature. Check that the supply system has an effective earth connection and meets the standards and
that the breaker can be reached easily when the appliance is installed.
When a cable is damaged or must be replaced, the operation must be carried out the by a service agent or
a suitably qualified professional.
When the appliance is being connected directly to the mains, an omnipolar circuit breaker must be installed
with a minimum opening of 3mm between contacts.
The installer must ensure that the correct electrical connection has been made and that it is compliant with
all applicable standards and safety regulations.
The cable must not be bent or compressed.
The cable must be checked regularly and replaced by authorised technicians only.
TERMINAL BOARD
Recommended
type of
connection lead
CONNECTION DIAGRAM
Caution! Voltage of heating elements 220-240V
Caution! In the event of any connection the safety
wire must be connected to the E terminal.
For 220-240V earthed one-phase connection, bridges
connect L①-②-③ terminals and N④-⑤ terminals,
safety wire to
E
N
L
①
②
④
⑤
①
②
④
⑤
③
③
TECHNICAL INFORMATION FOR INSTALLATION PERSONNEL
This appliance must be installed only by authorised personnel and in accordance with the regulations of
electricity authorities. The wall and bench surfaces must be capable of sustaining temperatures of 95
degrees Celsius. All laminates, fixing adhesive and surfacing materials should be certified suitable for this
temperature. Do not install it in areas with combustible materials.
According to the pictures, cut the hole in bench and place the built-in electric hob in it.
Your hob can be fitted to any worktop with a thickness of 40 to 50 mm.
Unit:mm
Inserting and fixing the hob
Before inserting the hob into the work surface, place the adhesive seal “s” around the underside edge of the
hob. It is important to fix this gasket evenly without gaps or overlap to prevent liquids from seeping underneath
the hob.
1.Place the gasket around the bottom edge of the hobs as shown in the illustration overleaf.
2.Place the hob in the installation opening and push it down so that the hob is resting frimly on the cabinet.
3.Secure the hob in position using the fixing brackets supplied.
Fitting guidelines
Secure the hob to the underside of the worktop using the fixings provided.
Screw one end of the bracket into the pre-drilled holes in the underside of the hob. The other end of the bracket should be
located underneath the worktop to secure the hob in position
Note 1:
Fire resistant material (e.g. ceramic tiles) are required to 450mm above burner top if wall or vertical structures are not
permitted within 200mm from burner.
Note 2:
No overhanging surface or rangehood / exhaust system are permitted within 600mm above cooktop.
Note 3:
Leave at least 50mm clearance between the base of the appliance and a combustible surface. Never leave the packing
components (plastic bags, nails, foamed polystyrene, etc.) within the reach of the children since they are a source of potential
danger.
The hob has a special seal which prevents liquid from entering the cabinet. Follow these instructions in order to correctly apply
it.
Seal:
Detach the seal/s from their backing, ensure that the transparent protection still adheres to the seal itself. Turn over the hob
and correctly position seal under the edge of the hob, so that the outer part of the seal perfectly matches the outer edge of the
hob. Press the seal firmly in place to fix the seal to the hob.
By ensuring that this appliance is disposed of correctly, you will help prevent any possible harm to
The environment and to human health which might otherwise be caused if disposed of in the
wrong way.
The symbol on the product indicates that it may not be treated as normal household waste.
It should be taken to a collection point for the recycling of electrical and electronic goods.
For further information regarding the treatment, recovery and recycling of this product, please contact
your local council, household waste disposal service or the shop where you purchased the product.
CLEANING AND MAINTENANCE
- Do not use cleaning products containing abrasive materials for the cleaning and maintenance of the glass.
e.g. scouring powders containing an abrasive, abrasive compounds, abrasive stones, pumice stones, wire
brushes and so on. They may scratch the hob surface, causing irreversible damage.
- Large spillages that are firmly burnt onto the hob can be removed using a special scraper; be careful not
to damage the ceramic hob surface when doing this.
Caution! The scraper sharp blade should always be protected by adjusting the cover (just push it with your
thumb). Injuries are possible so be careful when using this instrument, keep it out of reach of children.
Appropriate light cleaning products are recommended e.g. any kind of liquid detergents. Alternatively a
solution of warm water with a little dishwashing liquid or cleaning products for stainless steel sinks can be
used.
Disassembly bottom base
Bottom base removal is only to be done by a qualified service person.
4 screws need to be removed first before bottom base disassembly.
The manufacturer refuses all responsibility if the standards in force are not respected.
PROBLEM
Hob doesn't work
SOLUTION
•Check the power connection
•Check the safety cutoff switch is OFF
•Check the fuse and the mains current limit
There is some smoke when
the hob is working
•It is normal the first time use.
•Clean around the electric hob and the
cooking zones
The wire/s are damaged
•Contact the nearest maintainance
centre for service/ repair.
MALFUNCTION ELIMINATION
600-750
450
860
830
490
520
77
72
Ventilation slot ≥ 30mm
50mm MIN.
50
200
200
Rear wall
Front edge of worktop
Loading ...
Loading ...
Loading ...