Loading ...
Loading ...
Loading ...
Cabinet Opening Dimensions
Clearances
Check that all surfaces have no protrusions that would prohibit
dishwasher installation.
34"
4"
3"
24"
2"
(864 mm)
B
A
(102 mm)
(76 mm)
(620 mm)
24"
(620 mm)
(51 mm)
(159 mm)
(172 mm)
(267 mm)
3
/
4
"
6
1
/
4
"
(64 mm)
2
1
/
4
"
6
(44 mm)
1
3
/
4
"
10
1
/
2
"
A. Measured from the lowest point on the underside of the countertop.
May be reduced to 33
1
/
2
" (851 mm) by removing the wheels and
perforated area of insulation (blanket) on dishwasher.
B. Minimum, measured from narrowest point of opening.
NOTE: Shaded areas of cabinet walls show where utility
connections may be installed.
Drain Requirements
� A new drain hose is supplied with your dishwasher. If drain
hose is not long enough, use a new drain hose with a
maximum length of 12 ft (3.7 m) that meets all current AHAM/
IAPMO test standards, is resistant to heat and detergent, and
fits the 1" (25 mm) drain connector of the dishwasher.
NOTE: Do not connect multiple drain hoses together.
� Make sure to connect drain hose to waste tee or disposer inlet
above drain trap in house plumbing and 20" (508 mm)
minimum above the floor. It is recommended that the drain
hose either be looped up and securely fastened to the
underside of the counter or be connected to an air gap.
� Make sure to use an air gap if the drain hose is connected to
house plumbing lower than 20" (508 mm) above subfloor or
floor.
A
A. Air gap
� If required, the air gap should be installed in accordance with
the air gap installation instructions. When you are connecting
the air gap, a rubber hose (not provided) will be needed to
connect to the waste tee or disposer inlet.
� Use 1/2" (12.7 mm) minimum I.D. drain line fittings.
Water Supply Requirements
� This dishwasher has a water heating feature and also requires
a connection to a hot water supply line.
� A hot water line with 20 psi to 120 psi (138 kPa to 827 kPa)
water pressure can be verified by a licensed plumber.
� 120°F (49°C) water at dishwasher
� 3/8" (9.5 mm) O.D. copper tubing with compression fitting or
flexible braided water supply line
NOTE: 1/2" (12.7 mm) minimum plastic tubing is not
recommended.
� A 90° elbow with 3/4" (19 mm) hose connection with rubber
washer
� Do not solder within 6" (152 mm) of the water inlet valve.
� If installed in new construction, make sure the house water
supply lines have been flushed prior to connecting the
dishwasher to remove any debris that may exist in the supply
line.
NOTE: If replacing an existing dishwasher, it is recommended to
install a new water line and drain hose (supplied) with the new
dishwasher.
Electrical Requirements
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code, ANSI/NFPA
70 – latest edition, and all local codes and ordinances.
For a fee, a copy of the above code standards can be obtained
from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
You Must Have:
� 120 V, 60 Hz, AC-only, 15 A or 20 A, fused electrical supply.
� Copper wire only.
� A maximum of 2 field wiring supply conductors (12 AWG
largest size) plus 1 grounding conductor are permitted in the
terminal box.
We Recommend:
� A time-delay fuse or circuit breaker.
Circuit Requirement:
� The dishwasher may be installed on the same circuit as a
garbage disposal providing that the branch circuit cannot
exceed rated circuit load and must comply with all governing
codes and regulations such as but not limited to National
Electrical Code, ANSI/NFPA 70 - latest edition.
� No electrical connections other than the dishwasher power
and ground connections can be made inside of the dishwasher
terminal box.
If Connecting Dishwasher with a Power Cord:
� Use a UL-listed power cord kit
marked for use with dishwasher. See
the “Tools and Parts” section for part
details.
� Plug into a grounded 3-prong outlet.
Outlet must meet all local codes and
ordinances.
8
Loading ...
Loading ...
Loading ...