Ceramic
Oscillating
Heater
KCE95
Instruction Booklet
Kambrook - Australia
Building 2, Port Air Industrial Estate
1A Hale Street
Botany NSW 2019
Australia
Customer Service Line 1300 139 798
Customer Service Fax 1800 621 337
www.kambrook.com.au
Due to continual improvement in design or otherwise, the product you
purchase may differ slightly from the illustration in this book. Issue A11
Kambrook - New Zealand
Private Bag 94411
Botany, Manukau
Auckland 2163
New Zealand
Customer Service Line/
Spare Parts 0800 273 845
Customer Service Fax 0800 288 513
www.kambrook.co.nz
Contents
Kambrook Recommends p4
Safety First
Your Ceramic Oscillating Heater p6
Quick Start Guide p7
Using Your Ceramic p8
Oscillating Heater
Care and Cleaning p10
Important
Please retain your instruction
book for future use.
In the event that you need some assistance with your
Kambrook appliance, please contact our Customer Service
Department on 1300 139 798 (Australia) or 0800 273 845
(New Zealand). Alternatively, visit us on our website at
www.kambrook.com.au or www.kambrook.co.nz
Contents
Kambrook Recommends p4
Safety First
Your Ceramic Oscillating Heater p6
Quick Start Guide p7
Using Your Ceramic p8
Oscillating Heater
Care and Cleaning p10
Important
Please retain your instruction
book for future use.
In the event that you need some assistance with your
Kambrook appliance, please contact our Customer Service
Department on 1300 139 798 (Australia) or 0800 273 845
(New Zealand). Alternatively, visit us on our website at
www.kambrook.com.au or www.kambrook.co.nz
4 5
Kambrook Recommends Safety First
IMPORTANT: Please retain your
instruction book for future use.
At Kambrook, we believe that safe performance is the first priority in any
consumer product, so that you, our valued customer can confidently
use and trust our products. We ask that any electrical appliance that
you use be operated in a sensible fashion with due care and attention
placed on the following important operating instructions.
Important Safeguards For Your Kambrook
Ceramic Oscillating Heater
• Carefully read all instructions before operating the
Heater and save for future reference.
• Remove any packaging material and promotional
stickers before using the heater for the first time.
• Connect only to 230V or 240V power outlet.
• Avoid touching heater body while it is on, some
parts of the heater are hot. When moving the unit
switch off and hold the Heater by the handles
where provided.
• Keep combustible materials such as drapes and
other furnishings at least 1.7 metres from the front,
sides and rear of the heater. Do not use heater to
dry your laundry.
• Extreme caution and supervision is necessary
when this heater is used by or near children,
invalids or animals.
• Children should be supervised to ensure that they
do not play with the heater.
WARNING: In order to
avoid overheating, do
not cover the heater.
IMPORTANT: This heater
is intended for floor use
only. Do not mount on
ceiling or walls.
• Do not operate the heater on an incline plane. Do
not leave while the heater is switched on.
• Do not leave heater unattended. Always switch
off the heater at the controls and at the power
outlet then unplug heater from the power outlet
when not in use.
• Do not operate heater whilst asleep.
• Do not operate any heater with a damaged
cord or plug, or if heater has been dropped or
damaged in any manner. Return heater to your
nearest Kambrook service centre for examination,
electrical or mechanical adjustment or repair.
• Do not operate the heater with the power cord
damaged, frayed or split, wound around any part
of the heater, or in contact with heated surfaces
of the heater.
• Do not run the cord under carpeting or cover the
cord with rugs, runners or the like. Arrange cord
away from traffic areas and where it will not be
tripped over.
• Do not locate the heater immediately below a
socket outlet when in use.
• Do not use this heater with a programmer, timer
or any other device that switches the heater
on automatically since a fire risk may exist if the
heater is covered or positioned incorrectly.
• This heater is not intended for use in wet or moist
locations. Do not use this heater in the immediate
surroundings of a bath, a shower or a swimming
pool. Do not immerse or allow liquids to be spilt
on heater.
• Do not use the heater to dry your laundry.
• This heater has hot and arcing or sparking parts
inside. Do not use in areas where petrol, paints,
aerosols, or other inflammable substances are
used or stored.
• Do not allow materials that have been in contact
with oil, petroleum based products or drying fluids
to come in contact with the heater.
• To disconnect heater switch the power On/Off
switch to OFF, then switch off at the power outlet
then remove plug from its outlet.
• Do not insert or allow foreign objects to pass
through the inlet or outlet openings. This may
cause an electric shock, fire or damage
the heater.
• To prevent a possible fire or heat damage, allow
ample space around the heater (at 1.7m at front
and 0.5m at the rear, top and sides) and do not
totally or partially block the air inlet or outlets
in any manner. Check the openings from time
to time for accumulated dust. Ensure long shag
carpet does not obstruct airflow under the unit.
• Do not touch hot metal surfaces.
• Switch off at the power On/Off switch and power
outlet, then unplug and allow heater to cool down
before cleaning or storing.
• Do not use outdoors. This heater is not intended for
commercial use such as construction sites.
• Use this heater only as described in this instruction
manual. Any other use not recommended by the
manufacture may cause fire electric shock or
injury and voids all warranties.
• Regularly inspect the supply cord, plug, control
settings, air inlets and outlets and main housing
for any damage. If found damaged in any way,
immediately cease use of the heater and return
to Kambrook or an authorised service agent for
inspection or repair.
NOTE: This Kambrook Ceramic
Heater is electronically
controlled and will not operate
until the heater is plugged into
a 230V or 240V power point and
switched on.
Important Safeguards For All Electrical
Appliances
• Carefully read all instructions before operating the
appliance and save for future reference.
• Remove and safely discard all packaging
material and promotional labels before using the
appliance for the first time.
• Fully unwind the power cord before use.
• Do not let the power cord hang over the edge of
a bench or table, touch hot surfaces or become
knotted.
• To protect against electric shock, do not immerse
the power cord, power plug or appliance in water
or any other liquid, unless it is recommended in the
cleaning instructions.
• The appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance, by a person responsible for their safety.
• Children should be supervised to ensure that they
do not play with the appliance.
• It is recommended to inspect the appliance
regularly. Do not use the appliance if the power
supply cord, plug, connector or appliance
becomes damaged in anyway. Return the entire
appliance to the nearest authorised Kambrook
Service Centre for examination and/or repair.
• Any maintenance other than cleaning should
be performed at an authorised Kambrook
Service Centre.
• This appliance is for household use only. Do not use
this appliance for other than its intended use. Do
not use in moving vehicles or boats.
Do not use outdoors. Misuse may cause injury.
• The installation of a residual current device (safety
switch) is recommended to provide additional safety
protection when using electrical appliances. It is
advisable that a safety switch with a rated residual
operating current not exceeding 30mA be installed
in the electrical circuit supplying the appliance. See
your electrician for professional advice
• Always turn the appliance to the OFF position,
switch off at the power outlet and unplug at the
power outlet when the appliance is not in use.
• Before cleaning, always turn the appliance to the
OFF position, switch off at the power outlet, unplug
at the power outlet and remove the power cord,
if detachable, from the appliance and allow all
parts to cool.
• Do not place this appliance on or near a heat
source, such as hot plate, oven or heaters.
• Position the appliance at a minimum distance
of 20cm away from walls, curtains and other
heat or steam sensitive materials and provide
adequate space above and on all sides for air
circulation.
4 5
Kambrook Recommends Safety First
IMPORTANT: Please retain your
instruction book for future use.
At Kambrook, we believe that safe performance is the first priority in any
consumer product, so that you, our valued customer can confidently
use and trust our products. We ask that any electrical appliance that
you use be operated in a sensible fashion with due care and attention
placed on the following important operating instructions.
Important Safeguards For Your Kambrook
Ceramic Oscillating Heater
• Carefully read all instructions before operating the
Heater and save for future reference.
• Remove any packaging material and promotional
stickers before using the heater for the first time.
• Connect only to 230V or 240V power outlet.
• Avoid touching heater body while it is on, some
parts of the heater are hot. When moving the unit
switch off and hold the Heater by the handles
where provided.
• Keep combustible materials such as drapes and
other furnishings at least 1.7 metres from the front,
sides and rear of the heater. Do not use heater to
dry your laundry.
• Extreme caution and supervision is necessary
when this heater is used by or near children,
invalids or animals.
• Children should be supervised to ensure that they
do not play with the heater.
WARNING: In order to
avoid overheating, do
not cover the heater.
IMPORTANT: This heater
is intended for floor use
only. Do not mount on
ceiling or walls.
• Do not operate the heater on an incline plane. Do
not leave while the heater is switched on.
• Do not leave heater unattended. Always switch
off the heater at the controls and at the power
outlet then unplug heater from the power outlet
when not in use.
• Do not operate heater whilst asleep.
• Do not operate any heater with a damaged
cord or plug, or if heater has been dropped or
damaged in any manner. Return heater to your
nearest Kambrook service centre for examination,
electrical or mechanical adjustment or repair.
• Do not operate the heater with the power cord
damaged, frayed or split, wound around any part
of the heater, or in contact with heated surfaces
of the heater.
• Do not run the cord under carpeting or cover the
cord with rugs, runners or the like. Arrange cord
away from traffic areas and where it will not be
tripped over.
• Do not locate the heater immediately below a
socket outlet when in use.
• Do not use this heater with a programmer, timer
or any other device that switches the heater
on automatically since a fire risk may exist if the
heater is covered or positioned incorrectly.
• This heater is not intended for use in wet or moist
locations. Do not use this heater in the immediate
surroundings of a bath, a shower or a swimming
pool. Do not immerse or allow liquids to be spilt
on heater.
• Do not use the heater to dry your laundry.
• This heater has hot and arcing or sparking parts
inside. Do not use in areas where petrol, paints,
aerosols, or other inflammable substances are
used or stored.
• Do not allow materials that have been in contact
with oil, petroleum based products or drying fluids
to come in contact with the heater.
• To disconnect heater switch the power On/Off
switch to OFF, then switch off at the power outlet
then remove plug from its outlet.
• Do not insert or allow foreign objects to pass
through the inlet or outlet openings. This may
cause an electric shock, fire or damage
the heater.
• To prevent a possible fire or heat damage, allow
ample space around the heater (at 1.7m at front
and 0.5m at the rear, top and sides) and do not
totally or partially block the air inlet or outlets
in any manner. Check the openings from time
to time for accumulated dust. Ensure long shag
carpet does not obstruct airflow under the unit.
• Do not touch hot metal surfaces.
• Switch off at the power On/Off switch and power
outlet, then unplug and allow heater to cool down
before cleaning or storing.
• Do not use outdoors. This heater is not intended for
commercial use such as construction sites.
• Use this heater only as described in this instruction
manual. Any other use not recommended by the
manufacture may cause fire electric shock or
injury and voids all warranties.
• Regularly inspect the supply cord, plug, control
settings, air inlets and outlets and main housing
for any damage. If found damaged in any way,
immediately cease use of the heater and return
to Kambrook or an authorised service agent for
inspection or repair.
NOTE: This Kambrook Ceramic
Heater is electronically
controlled and will not operate
until the heater is plugged into
a 230V or 240V power point and
switched on.
Important Safeguards For All Electrical
Appliances
• Carefully read all instructions before operating the
appliance and save for future reference.
• Remove and safely discard all packaging
material and promotional labels before using the
appliance for the first time.
• Fully unwind the power cord before use.
• Do not let the power cord hang over the edge of
a bench or table, touch hot surfaces or become
knotted.
• To protect against electric shock, do not immerse
the power cord, power plug or appliance in water
or any other liquid, unless it is recommended in the
cleaning instructions.
• The appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance, by a person responsible for their safety.
• Children should be supervised to ensure that they
do not play with the appliance.
• It is recommended to inspect the appliance
regularly. Do not use the appliance if the power
supply cord, plug, connector or appliance
becomes damaged in anyway. Return the entire
appliance to the nearest authorised Kambrook
Service Centre for examination and/or repair.
• Any maintenance other than cleaning should
be performed at an authorised Kambrook
Service Centre.
• This appliance is for household use only. Do not use
this appliance for other than its intended use. Do
not use in moving vehicles or boats.
Do not use outdoors. Misuse may cause injury.
• The installation of a residual current device (safety
switch) is recommended to provide additional safety
protection when using electrical appliances. It is
advisable that a safety switch with a rated residual
operating current not exceeding 30mA be installed
in the electrical circuit supplying the appliance. See
your electrician for professional advice
• Always turn the appliance to the OFF position,
switch off at the power outlet and unplug at the
power outlet when the appliance is not in use.
• Before cleaning, always turn the appliance to the
OFF position, switch off at the power outlet, unplug
at the power outlet and remove the power cord,
if detachable, from the appliance and allow all
parts to cool.
• Do not place this appliance on or near a heat
source, such as hot plate, oven or heaters.
• Position the appliance at a minimum distance
of 20cm away from walls, curtains and other
heat or steam sensitive materials and provide
adequate space above and on all sides for air
circulation.
6 7
Your Ceramic Oscillating Heater
1. Carry handle (at back)
2. Power On/Off switch (at back)
3. 2 heat settings and fan
only setting
4. Thermostat control
5. Oscillating function
6. LED screen
7. 1800 watts ceramic
heating elements
Not Shown
• Safety tip-over cut-out switch
• ThermoGuard Protection
Pressing the
MODE button
again will set the
heater to HIGH
heat mode
(1800W).
Quick Start Guide
Turning the
heater on
Setting the
variable
temperature
Setting the
heating
mode
Setting the
oscillation
Turning the
heater off
When first
set to AUTO
mode, the LED
will display
the default
temperature
of 25°C and
will flash.
Plug the cord
into a 230V or
240V power
point and
switch on.
Once the LED
display flashes,
the desired
temperature
can be set by
adjusting the
thermostat
knob on the top
of the heater
Switch on using
the ON/OFF
switch on the
back of the
heater. A ‘beep’
will sound and
the power
indicator light
will illuminate.
Pressing the
MODE button
once more
will set the
heater into
the FAN mode.
‘FA’ and the
current room
temperature will
appear on the
LED display.
Press the
MODE button
to activate
heating. When
initially turned
on, the heater
will be in LOW
heat mode
(1100W) and the
current room
temperature will
appear on the
LED display
Press the
SWING button
to activate
oscillation. Press
again to stop
the oscillation.
To turn the
heater off, press
the MODE
button and hold
for 2-3 second
until you hear a
‘beep’. Switch
off using the
ON/OFF switch
on the back of
the heater
Pressing the
MODE button
a third time will
set the heater
into AUTO mode
(1800W)
6 7
Your Ceramic Oscillating Heater
1. Carry handle (at back)
2. Power On/Off switch (at back)
3. 2 heat settings and fan
only setting
4. Thermostat control
5. Oscillating function
6. LED screen
7. 1800 watts ceramic
heating elements
Not Shown
• Safety tip-over cut-out switch
• ThermoGuard Protection
Pressing the
MODE button
again will set the
heater to HIGH
heat mode
(1800W).
Quick Start Guide
Turning the
heater on
Setting the
variable
temperature
Setting the
heating
mode
Setting the
oscillation
Turning the
heater off
When first
set to AUTO
mode, the LED
will display
the default
temperature
of 25°C and
will flash.
Plug the cord
into a 230V or
240V power
point and
switch on.
Once the LED
display flashes,
the desired
temperature
can be set by
adjusting the
thermostat
knob on the top
of the heater
Switch on using
the ON/OFF
switch on the
back of the
heater. A ‘beep’
will sound and
the power
indicator light
will illuminate.
Pressing the
MODE button
once more
will set the
heater into
the FAN mode.
‘FA’ and the
current room
temperature will
appear on the
LED display.
Press the
MODE button
to activate
heating. When
initially turned
on, the heater
will be in LOW
heat mode
(1100W) and the
current room
temperature will
appear on the
LED display
Press the
SWING button
to activate
oscillation. Press
again to stop
the oscillation.
To turn the
heater off, press
the MODE
button and hold
for 2-3 second
until you hear a
‘beep’. Switch
off using the
ON/OFF switch
on the back of
the heater
Pressing the
MODE button
a third time will
set the heater
into AUTO mode
(1800W)
8 9
Using Your Ceramic Oscillating Heater
• Remove your heater from its carton and
associated protective wrapping.
• Unwind the cord to its full length and
remove any protective cardboard or
foam that may have been used to
minimise transportation damage. Place
the heater on a firm, level surface in a
stable upright position.
• Visually inspect the air inlet and outlets
to ensure no foreign material is blocking
these areas. The heater must always be
operated with the rear air filter
in position.
Turning Your Heater On
• Plug the cord into a 230V or 240V
electrical outlet. Be sure the plug
fits tightly as a loose fit will cause
overheating and damage the plug.
NOTE: To avoid an electrical
circuit overload, it is
recommended that no other
appliances are plugged into
the same circuit with your heater
when you switch the unit on.
• When the heater is initially plugged in
and the power switch is turned on at
the rear of the unit there will be a ‘beep’
and the power indicator will light up.
This indicates that the unit is powered.
The indicator will remain lit until the
power switch on the rear of the unit is
switched off.
• Turn the heat on by pressing the
MODE button.
• Upon turning the heater on, the unit will
be in the LOW heat mode (1100 watts),
‘LO’ and the current room temperature
will appear on the LED display.
• Pressing the MODE button again at this
stage will set the heater into the HIGH
heat mode (1800 watts), ‘HI’ and the
current room temperature will appear
on the LED display.
• Pressing the MODE button again will set
the heater into the AUTO mode (1800
watts). The LED will display the default
temperature of 25ºC and will flash. This
flash indicates you can set the desired
temperature via the thermostat knob on
the top of the unit.
• Pressing the MODE button once more
will set the heater into the FAN mode,
‘FA’ and current room temperature will
then appear on the LED display. FAN
mode is for fan-only operation with no
output of heat.
• Pressing the MODE button again will
cause the heater to go back to the
LOW heat mode. Continuing to press the
MODE button will cycle the unit through
LOW, HIGH, AUTO & FAN modes.
• To turn the heater off, press the MODE
button for approximately two to three
seconds until you hear a ‘beep’. Turn
off the power On/Off switch and power
outlet and remove the plug from the
power outlet.
NOTE: There is a tip-over
switch fitted to this heater. If
the heater is tipped over, it
will automatically turn off. The
heater will need to be placed
back into the upright position
to resume heating again.
Setting the Oscillation
This function will work in any mode.
Pressing the SWING button will allow
the heater to oscillate back and forth.
To stop the unit oscillating, press the
SWING button once more.
Setting the Variable
Thermostat Temperature
1. Press the MODE button until the
heater is set to the AUTO mode.
2. To adjust the set temperature,
rotate the Thermostat dial
clockwise to increase the desired
temperature and counter-
clockwise to decrease the desired
temperature.
3. The desired temperature can be
set between 15ºC and 38ºC.
4. When the air temperature
reaches 2ºC above the set
temperature the heater will stop
heating at once and stop blowing
after approximately 15 seconds.
5. When the air temperature drops
1ºC below the set temperature
the unit will reactivate.
Safety Features
This heater includes an audible alarm
to warn that parts of the heater are
overheating. If this alarm sounds,
immediately turn the heater off
and inspect for any objects on or
adjacent to the heater that may
cause high temperature.
WARNING: Do not
operate the heater with
the alarm sounding.
ThermoGuard Overheating
Safety Device
Your heater is fitted with a safety
device that switches off the heater
in the event of overheating. Should
this heater stop working, turn off the
heater and inspect the air inlet and
outlet for blockages. Wait until the
unit is fully cooled for the protection
system to reset before attempting to
restart the heater.
If the heater fails to operate or the
safety device switches off again,
return the heater to your nearest
service centre for examination
or repair.
8 9
Using Your Ceramic Oscillating Heater
• Remove your heater from its carton and
associated protective wrapping.
• Unwind the cord to its full length and
remove any protective cardboard or
foam that may have been used to
minimise transportation damage. Place
the heater on a firm, level surface in a
stable upright position.
• Visually inspect the air inlet and outlets
to ensure no foreign material is blocking
these areas. The heater must always be
operated with the rear air filter
in position.
Turning Your Heater On
• Plug the cord into a 230V or 240V
electrical outlet. Be sure the plug
fits tightly as a loose fit will cause
overheating and damage the plug.
NOTE: To avoid an electrical
circuit overload, it is
recommended that no other
appliances are plugged into
the same circuit with your heater
when you switch the unit on.
• When the heater is initially plugged in
and the power switch is turned on at
the rear of the unit there will be a ‘beep’
and the power indicator will light up.
This indicates that the unit is powered.
The indicator will remain lit until the
power switch on the rear of the unit is
switched off.
• Turn the heat on by pressing the
MODE button.
• Upon turning the heater on, the unit will
be in the LOW heat mode (1100 watts),
‘LO’ and the current room temperature
will appear on the LED display.
• Pressing the MODE button again at this
stage will set the heater into the HIGH
heat mode (1800 watts), ‘HI’ and the
current room temperature will appear
on the LED display.
• Pressing the MODE button again will set
the heater into the AUTO mode (1800
watts). The LED will display the default
temperature of 25ºC and will flash. This
flash indicates you can set the desired
temperature via the thermostat knob on
the top of the unit.
• Pressing the MODE button once more
will set the heater into the FAN mode,
‘FA’ and current room temperature will
then appear on the LED display. FAN
mode is for fan-only operation with no
output of heat.
• Pressing the MODE button again will
cause the heater to go back to the
LOW heat mode. Continuing to press the
MODE button will cycle the unit through
LOW, HIGH, AUTO & FAN modes.
• To turn the heater off, press the MODE
button for approximately two to three
seconds until you hear a ‘beep’. Turn
off the power On/Off switch and power
outlet and remove the plug from the
power outlet.
NOTE: There is a tip-over
switch fitted to this heater. If
the heater is tipped over, it
will automatically turn off. The
heater will need to be placed
back into the upright position
to resume heating again.
Setting the Oscillation
This function will work in any mode.
Pressing the SWING button will allow
the heater to oscillate back and forth.
To stop the unit oscillating, press the
SWING button once more.
Setting the Variable
Thermostat Temperature
1. Press the MODE button until the
heater is set to the AUTO mode.
2. To adjust the set temperature,
rotate the Thermostat dial
clockwise to increase the desired
temperature and counter-
clockwise to decrease the desired
temperature.
3. The desired temperature can be
set between 15ºC and 38ºC.
4. When the air temperature
reaches 2ºC above the set
temperature the heater will stop
heating at once and stop blowing
after approximately 15 seconds.
5. When the air temperature drops
1ºC below the set temperature
the unit will reactivate.
Safety Features
This heater includes an audible alarm
to warn that parts of the heater are
overheating. If this alarm sounds,
immediately turn the heater off
and inspect for any objects on or
adjacent to the heater that may
cause high temperature.
WARNING: Do not
operate the heater with
the alarm sounding.
ThermoGuard Overheating
Safety Device
Your heater is fitted with a safety
device that switches off the heater
in the event of overheating. Should
this heater stop working, turn off the
heater and inspect the air inlet and
outlet for blockages. Wait until the
unit is fully cooled for the protection
system to reset before attempting to
restart the heater.
If the heater fails to operate or the
safety device switches off again,
return the heater to your nearest
service centre for examination
or repair.
10 11
Always turn off and then unplug the
heater before cleaning.
Use only a clean, dry cloth to clean the
external surfaces of the heater only.
If the heater has collected dust or
dirt inside the unit or around the
elements, have the unit cleaned by
a qualified service agent. Do not
operate the heater in this condition.
Do not attempt to open the case of
the heater at any time, there are no
customer serviceable parts inside
When not in use, pack the heater,
preferably in its original box for best
protection and store in a cool, clean
and dry location.
Regularly clean the air filter at the
rear of the heater.
Care and Cleaning
Notes
• Fit window coverings like curtains to
halve winter heat loss
• Put draft stoppers, such as a rolled
up towel, at the bottom of outside
doorways to keep out cold air
• Keep the heat in and the cold out by
installing wall and ceiling insulation
• Avoid placing items too close to the
heater (both at the front and back)
for optimal air flow
Hints/Tips to Retain Heat in Your Home
• Don’t overheat your home. The
temperature of a heated room in
winter should be 18-21°C
• Your heater will work more
efficiently if you stick to Kambrook’s
recommended clearance spaces
• Choose the right size heater for the
room type you want to heat
• Zone off unoccupied rooms by
closing doors and only heat the
main living areas
10 11
Always turn off and then unplug the
heater before cleaning.
Use only a clean, dry cloth to clean the
external surfaces of the heater only.
If the heater has collected dust or
dirt inside the unit or around the
elements, have the unit cleaned by
a qualified service agent. Do not
operate the heater in this condition.
Do not attempt to open the case of
the heater at any time, there are no
customer serviceable parts inside
When not in use, pack the heater,
preferably in its original box for best
protection and store in a cool, clean
and dry location.
Regularly clean the air filter at the
rear of the heater.
Care and Cleaning
Notes
• Fit window coverings like curtains to
halve winter heat loss
• Put draft stoppers, such as a rolled
up towel, at the bottom of outside
doorways to keep out cold air
• Keep the heat in and the cold out by
installing wall and ceiling insulation
• Avoid placing items too close to the
heater (both at the front and back)
for optimal air flow
Hints/Tips to Retain Heat in Your Home
• Don’t overheat your home. The
temperature of a heated room in
winter should be 18-21°C
• Your heater will work more
efficiently if you stick to Kambrook’s
recommended clearance spaces
• Choose the right size heater for the
room type you want to heat
• Zone off unoccupied rooms by
closing doors and only heat the
main living areas
Ceramic
Oscillating
Heater
KCE95
Instruction Booklet
Kambrook - Australia
Building 2, Port Air Industrial Estate
1A Hale Street
Botany NSW 2019
Australia
Customer Service Line 1300 139 798
Customer Service Fax 1800 621 337
www.kambrook.com.au
Due to continual improvement in design or otherwise, the product you
purchase may differ slightly from the illustration in this book. Issue A11
Kambrook - New Zealand
Private Bag 94411
Botany, Manukau
Auckland 2163
New Zealand
Customer Service Line/
Spare Parts 0800 273 845
Customer Service Fax 0800 288 513
www.kambrook.co.nz
