Loading ...
IMPORTANT INFORMATION
FOR NEW APPLIANCE OWNERS
Q. My appliance makes a noise when I use the oven. Is this Q.
normal?
A. Yes. Changes in temperature can cause metal to expand and A.
contract.
Q. My oven door has a soft spongy feel when closed; is
there something wrong with the door seal?
A. There is nothing wrong with the seal. The soft feel is normal
and the seal will "give" slightly as the door is pushed inward
against the oven's front frame. The spongy feel is due to the
door gasket design that ensures proper sealing.
Q. My range was just installed and only the surface burners
are heating, the oven does not; is this normal?
A. During installation the installer accidentally turned the gas
off to the oven burner. On ranges with electric ignition, there
is a shut off "lever" located on the pressure regulator. This
lever must be pointing to the "side", not downward for the
oven to operate. The regulator is located where the gasflex
line isattached to the range; consult your Installation Instruc-
tions for an illustration and location.
For Models with Gas Cooking Surface
Q. When I turn on one of the surface burner valves, I notice
that each of the surface electrodes sparks at the same
time. Is this normal?
A. It's normal for all the surface electrodes to spark at the same
time, but only the burner being turned ON will light.
Q. I have a problem of ignition with one burner; what can I
do?
A. Problem of burner ignition can be caused by a bad installa-
tion of the two main pieces; the burner and the burner cap
must be positioned adequately by the customer or the tech-
nician (Sealed burners only). (see installation instructions)
Q. The burner flame is out, bad or strong. Can I adjust it?
A. The flame height can be adjusted by removing the control
knob and screw slightly the adjustable screw of the valve to
the desired setting. For more information refer to your in-
stallation instructions.
My range is equipped with "Cast Iron" burner grates, I
have noticed rust is starting to form on the bottom.
The bottom surfaces on "Cast Iron" grate are deliberately
unfinished to allow the "high carbon" gasesthat are present
in iron to escape during the manufacturing process. If the
gases were trapped, it would cause surface blemishes in the
enamel finish and increase chipping. To eliminate or mini-
mize rust from forming, don't allow grates to stand in wa-
ter for long periods of time. After washing, dry them thor-
oughly to prevent rust oxidation from forming. You may also
coat the bottom surfaces with a "Vegetable Oil", or a "Non
Stick" cooking spray, but remember to wipe off excessive oil
before placing on range. There maybe a slight amount of
smoke from any extra vegetable oil residue left on the grate
when the burner is first used again.
Q. The pilot light (for models without electric ignition) is
out or is too strong, it seems that it needs to be ad-
justed?
A. It is possible for you to adjust the pilot light by lifting the top
and screw or unscrew the pilot screw on the manifold. For
more details refer to your Use and Care Guide.
Q. The porcelain enamel is hot even when I don't use it. Is
it normal?
A. Yes. The pilot light flame is always on, but if it is too strong,
you can adjust it. See your Use and Care Guide for more
information.
For Wall Ovens Models:
Q. What can I do if myself-clean side swing oven door istoo
tight to open or if it doesn't close well?
A. For aself-clean oven with a side swing door, there is an ad-
justable bracket on the front frame under the door on the
handle side. If the door is too loose, lift up the bracket and if
it's too tight, push on it.
Q. There isa nylon or plastic spacer (some models) located
on the side or at the back of my oven; can I remove it to
help me to put my oven in place?
A. No. These spacers are requested to insure proper working,
good air circulation and to prevent possible damage to your
cabinet. If there is no spacer on your built-in oven, it is be-
cause your model does not need one.
Q. What phone number can I call to ask other questions I
may have about my appliance?
A. See your Use and Care Guide for a complete list of phone
numbers if you have questions, comments or if you need to
schedule service or purchase parts.
318202315 (0009) Rev. A