Loading ...
Loading ...
THANK YOU FOR BUYING A HOTPOINT PRODUCT.
In order to receive a more complete assistance, please
register your product on www.hotpoint.eu/register
Policies, standard documentation, ordering of spare parts and additional product information can be
found by:
• Visiting our website docs.hotpoint.eu and parts-selfservice.whirlpool.com
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identi cation plate.
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance, please
register your product on www.whirlpool.com.sg
For Singapore Warranty, please scan QR code or visit the website: www.whirlpool.com.sg
Standard documentation and additional product information can be found by:
• Visiting our website www.whirlpool.com.sg
• Using QR Code
• Alternatively, contact our After-sales Service (+65 6250 6888). When contacting our After-sales Service,
please state the codes provided on your product’s identi cation plate.
EN
Quick guide
Before using the appliance carefully read the Safety
Instructions.
xxxxxxxxxxxx
xxxx
*MAX LOAD 8 kg (Dry load)
Power consumption
o-mode (Po) - Watts 0.15
left-on mode (Pl) - Watts 0.15
Programmes kg kWh Minutes
Eco Cotton *
8 4.75 156
Eco Cotton
4 2.55 87
Synthetics 4 2.26 110
*This is the most ecient programmes in terms of energy consuption
and is suitable for drying normal wet cotton laundry. The values on
the Energy Label are based on this programme.
*MAX LOAD 9 kg (Dry load)
Power consumption
o-mode (Po) - Watts 0.15
left-on mode (Pl) - Watts 0.15
Programmes kg kWh Minutes
Eco Cotton *
9 5.23 162
Eco Cotton
4.5 2.79 92
Synthetics 4 2.26 110
*This is the most ecient programmes in terms of energy consuption
and is suitable for drying normal wet cotton laundry. The values on
the Energy Label are based on this programme. The values reported in
the table are obtained with the condensed water drained externally
through the drain hose.
CARE AND MAINTENANCE
WARNING: unplug the dryer during the cleaning and
maintenance procedures.
Emptying the water tank after each cycle (see Fig. A).
Pull the container out of the dryer and empty it into a sink or
other suitable drain, then place it back properly. Do not use the
dryer without having inserted the container back in place.
Cleaning the door lter after each cycle (see Fig. B).
Pull the lter out and clean it by removing the lint from the lter
surface under running water or using a vacuum cleaner. For optimal
performance, dry up the lter before inserting it back in place.
Do not use the dryer without having reinserted the lter in place.
Remove the door lter as described below:
1. Open the door and pull the lter upwards.
2. Open the lter and remove the lint from all its parts. Replace
the lter correctly making sure it is fully seated.
The lter is an essential part for drying. It is intended to
collect the lint formed during the drying process. If the
lter is clogged, the air ow inside the dryer can become
seriously aected: this will increase the drying time and
energy consumption, and could damage the dryer. If this
procedure is not carried out properly, the dryer may not
start.
Cleaning the condenser unit (see Fig. C).
Remove the condenser unit regularly (monthly) and clean o
any u deposits from the plates by running cold water along
its rear end. The light on after several cycles is just a reminder to
carry on this activity periodically.
Removing the condenser:
1. Open the condenser cover, unlock the three catches by
turning them 90° anticlockwise.
2. Pull on the grip to remove the condenser.
3. Clean the surface of the seals.
4. Replace the unit with the arrows pointing upwards, while
making sure that the catches are securely xed.
PRODUCT DESCRIPTION
1. Water tank
2. Air intake
3. Door lter
4. Condenser unit
5. Condenser cover
AB
C
1
3
2
4
5
Cleaning the tumble dryer
• The external metal, plastic and rubber parts can be cleaned
with a damp cloth.
• Clean the front air intake grille regularly (every 6 months)
with a vacuum cleaner to remove any lint, u or dust
deposits. Furthermore, remove any lint deposits from the
front part of the condenser and from the lter area, using a
vacuum cleaner every so often.
• Do not use solvents or abrasives.
Loading ...