Loading ...
Loading ...
Loading ...
IIIII I IIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIIIIIIIIII IIIIII IIIIIIIIIIIIIIII I
BEFORE YOU CALL FOR SERVICE
Check these points if your
washer...
Won't fill
• Plug cord into live electrical outlet.
• Check fuse or reset circuit breaker.
• Turn the control knob to proper cycle and pull
knob out to start the washer, tf equipped with
buttons, be sure they are fully depressed.
• Turn both faucets on fully.
• Straighten inlet hoses.
• Disconnect hoses and check hose filter screens.
Clean screens, if plugged.
Won't agitate
• Check fuse or reset circuit breaker.
• Turn the control knob to proper cycle and pull
knob out to start the washer. If equipped with
buttons, be sure they are fully depressed.
• Close lid and pull knob out to start the washer.
Foryour safety,washer will notagitate or spin
unlessthe lid is closed.
• The washer is equipped with a lid switch failure
detector. In the event that the lid switch should
malfunction, the detector will stop operations
for your safety. Call for service.
Won't spin or drain
• Check fuse or reset circuit breaker.
• Straighten hoses. Eliminate kinked hoses. If
there is a drain restriction, call for service.
• Close lid and pull knob out to start washer. For
your safety, washer will not agitate or spin
unlessthe lid isclosed.
• Off-balanced load. Redistribute the load evenly,
close lid and pull knob out. Checkfor leveling.
Be sure water level is acceptable for load size.
• Suds lock - caused by too much suds. Rewash
without detergent. Use correct amount of a low-
sudsing detergent.
• The washer is equipped with a lid switch failure
detector. In the event that the lid switch should
malfunction, the detector will stop operations
for your safety. Catl for service.
Stops
• P_ugcord into live electrical outlet.
• Check fuse or reset circuit breaker.
• Turn the control knob to proper cycle and pull
knob out to start the washer, tf equipped with
buttons, be sure they are fully depressed.
• Close lid and pull knob out to start the washer.
Foryour safety,washer will not agitate or spin
unlessthe lid isclosed.
• Off-balanced load. Redistributetheload evenl)
close lid and pull knob out. Check for leveling.
Be surewater level isacceptable for toad size.
• Thismay be a pause or soak period in the
cycle. Wait briefly and it may start.
• The washer isequipped with a lid switchfailur
detector.In the eventthat the lid switchshould
malfunction,the detectorwill stopoperations
for your safety. Call for service.
Leaks water
• Make sure hose connections are tight.
• Make sure end of drain hose is correctly
inserted in and secured to drain facility.
Is noisy
• Make surewasher is leveland firm tothe floo
Fills with the wrong temperature
water
• Turn both faucets on futly.
• If equipped with a temperature setector knob,
be sure it is set directly on a temperature settir
and not between settings.
• Make sure temperature selection is correct.
• Make sure hoses are connected to correct
faucets and inletconnections. Be sure water
supply is regulated correctly. Flushwater line
before filfing washer.
• Check the water heater. It should be set to
deliver a minimum 120°F 149°C) hot water a
the tap. Also check water heater capacity ar
recovery rate.
• Hose filter screens plugged. Disconnect hose.
and clean screens.
NOTE: For further assistance contact your
Maytag dealer or call Maytag Custom,
Service:
U.S. 1-800-688-9900
Canada 1-800-688-2002
PAGE 8 I,III IIIIIIIIIIIIIIIIII III
Loading ...