Contents
Safety
Instructions
………………………………………
. 3-5
Electrical
Safety
………………………………………
. 5
Transportation and Handling
………………………………………
. 5
In
stalling and Switching on Your Appliance
………………………………………
. 6
Before
Switching On
………………………………………
. 7
Your
Appliance & the Compartments
………………………………………
. 8
Unit
& Spare Parts
……………………………………….
8
Where to put your appliance
………………………………………
. 9
Installation
……………………………
.………… 10
Usage
Information
……………………………………….
11-13
Cleaning
& Maintenance
………………………………………
. 14
Defrosting
………………………………………
. 14
Important
Notes
……………………………………….
14
Connection
to the Mains Supply
……………………………………….
15
Troubleshooting
………………………………
.……… 16-17
Guarantee
………………………………………
. 18
Technical
specification
…………………………
.…………… 19
Safety Instructions
This appliance is a Semi-conductor electric refrigerating appliance, which is a
Category 10 other appliance, according to ErP 643/2009. Its design temperature is
17°C.
Important note: Please read this booklet before installing and switching on this
appliance. The manufacturer assumes no responsibility for incorrect installation
and usage as described in this booklet.
Warning: When positioning the appliance, ensure the supply cord is not
trapped or damaged.
Warning: Do not locate multiple portable socket-outlets or portable power
suppliers at the rear of the appliance.
• Do not obstruct ventilation openings in the appliance
• The appliance must not be placed or rested on its power cord.
• Do not use mechanical devices or other artificial means to accelerate the
defrosting process, such as a heater or a hair dryer.
• Do not use electrical appliances in the refrigerator compartment of the
appliance.
• If this appliance is to replace an old refrigerator with a lock, the lock must be
removed as a safety measure before storing it or disposing of it. This is to
protect children from locking themselves inside the appliance.
• Old refrigerators and freezers contain insulation gases and refrigerant, they
must be disposed of properly. Contact your local authority or your dealer if
you have any questions. Please ensure that you do not damage the scrap unit
prior to being picked-up by the relevant waste disposal service.
• Do not use adaptors or extension leads when connecting the appliance to the
electrical power supply
3
• Do not plug in damaged plugs.
• Do not pull, twist or damage the power cable.
• Do not plug-in or un-plug the appliance with wet hands to prevent electrical
shock.
• This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children should not play with the appliance.
• Children aged from 3 to 8 years are allowed to load and unload this appliance.
• This appliance is designed to be used by adults, do not allow children to play
with the appliance or let them hang over the door.
• Do not place explosive or flammable material in your appliance for your own
safety.
• Bottles containing a high percentage of alcohol must be sealed well and placed
vertically in the refrigerator.
• Do not cover the body or the top of the appliance
• Fix down the accessories in the appliance during transportation to prevent
damage to them.
• To avoid contamination of food, please respect the following instructions
• Opening the door for long periods can cause a significant increase of the
temperature in the compartments of the appliance.
• Clean regularly surfaces that can come in contact with food and accessible drainage
systems.
• If the appliance is left empty for long periods, switch off, defrost, clean, dry
and leave the door open to prevent mount developing within the appliance.
4
Electrical Safety
THIS APPLIANCE MUST BE PLUGGED INTO AN EARTHED SOCKET
• Before switching on, make sure that the voltage of your electricity supply is the
same as that indicated on the rating plate. This product is designed to operate
on 220 – 240V AC; 50Hz / DC 12V. Connection to any other power source may
damage the unit.
• This product may be fitted with a non re-wireable plug. If it is necessary to
change the fuse in the plug, the fuse cover must be refitted. If the fuse cover
becomes lost or damaged, the plug must not be used until a suitable
replacement is obtained.
• If the plug or adaptor has to be changed because it is not suitable for your
socket, or becomes damaged in any way, it should be cut off and an appropriate
plug fitted following the wiring instructions. This should be carried out by a
qualified electrician. The plug removed must be disposed of safely, as insertion
into a 13 Amp socket is likely to cause an electrical hazard.
Transportation and Handling
For safe lifting, ensure the door is closed and carry the appliance by the carry
handle. Lift the appliance carefully and Never use the door handles for lifting.
5
Installing and Switching on Your Appliance
• Operating voltage for your appliance is 220-240V at 50Hz / DC 12V .
• Before plugging in the power supply, ensure that the voltage on the rating
label corresponds to the working voltage of your electrical system in your home or
automobile.
• Insert the plug into an efficient Ground (Earth) connection. If the socket has no
Ground (Earth) contact or the plug does not match, we suggest you call an authorised
electrician for assistance.
• Place your appliance in an area that is not exposed to direct sunlight.
• Your appliance should be placed at least 10cm away from stoves, ovens and other
heating cores.
• This appliance should never be used outdoors or left in the rain.
• When your appliance is placed next to a chest freezer or freezer, there should be at
least 10cms between them to prevent humidity on the outer surface.
• Do not place anything on your appliance and install the unit in a suitable place so that
there is at least 30cm clearance above the appliance.
• The sides and rear of the appliance should have at least 10cm clearance.
• The appliance must be used in the vertical position and on a flat surface.
• To level the appliance, use the adjustable feet on the appliance.
• Do not place your appliance on a carpeted surface as this will prevent adequate
ventilation.
• This appliance should only be placed on a flat, firm surface.
• Choose a dry and well-ventilated space.
• The appliance should be positioned so that the plug is easily accessible.
• This appliance is not suitable for use in garages, outbuildings or rooms that do not
comply with the ambient temperature requirements set out in the Product Fiche.
• If you need help or are unsure how to install the unit, please contact Customer
Services on 0345 208 8750 or visit mda.russellhobbs.com.
6
Before Switching On
• Before using your appliance, add a teaspoon of bicarbonate of soda to warm
water and with a damp cloth wipe down all parts of the new appliance, then
repeat the process with a clean damp cloth and dry. (ensure the appliance is
not connected to the power when performing this task).
• Remove all transport tapes and foam protection pieces . Clean the interior with
a cloth dampened in lukewarm soap and water. Wipe with clean water and
wipe dry.
• There may be an odour when you first switch on the appliance, it will disappear
when the appliance starts to cool.
• When the appliance has been positioned, ensure the unit is stable. This is
essential to ensure quiet running and proper door opening/closing.
• Connect to the electrical socket (AC) or to a DC socket and set the mode switch
to Cold or Hot (the mode switch is located at the rear of the appliance) and
switch on the power. The appliance will begin to work.
• To save energy, you should minimize the frequency and duration of door
opening.
7
WARNING! During use, service and disposal of the appliance,
please pay attention to symbol similar to the one shown, which is
located on rear of the appliance (rear panel or compressor) and
with a yellow or orange colour. It’s risk of fire warning symbol.
There are flammable materials in refrigerant pipes and
compressor. Please be far away from fire source during use,
service and disposal.
1. Door handle
2. Door
3. Carry handle
4. Air inlet
5. Air outlet
6. Cooling indicator light
7. Heating indicator light
8. Off / Mode selection button
9. DC input
10. AC input
11. AC adaptor
12. DC adaptor
Your Appliance and the Compartments
Partsmay vary accordingto the appliance model.
8
Unit & Spare Parts
For spare parts please contact customer service on
0345 208 8750 or visit mda.russellhobbs.com
Item Quantity
Shelf 1
Instruction Booklet 1
Where to put your appliance
• This appliance should only be placed on a flat, solid surface.
• Do not place your appliance on a carpeted surface as this will prevent
adequate ventilation.
• Choose a dry and well-ventilated space. No less than 10mm (10cms) must be
left around the sides and 100mm (10cms) around the back of the appliance to
allow sufficient cooling.
• Choose a location away from a heat source, e.g. direct sunlight, a radiator or
oven, etc.
• The appliance should be positioned so that the plug is easily accessible.
9
(10cms)
(10cms)
(10cms)
Usage Information
Note:
• Do not use this appliance when engine if off to avoid running down
the car battery.
• The ambient temperature and air circulation condition can affect the
cooling speed and temperature of the appliance.
• The cooling temperature range of the appliance is between 18-22℃
below ambient temperature. For example if the ambient temperature
is 27℃ then the temperature inside the appliance will be between 5-
9℃ when set on Cold mode.
• The ideal ambient temperature for the appliance to perform is
between 20-25℃. The lowest temperature the appliance can achieve
is approximately 5℃.
• This appliance has a thermoelectric cooling system and not a
compressor cooling system (like a refrigerator) and therefore reach to
0℃ or achieve the same cooling performance.
• Heating temperature range 60℃ +/-5℃ when set to Hot mode.
• The temperature of freshly stored items and how often the door is
opened affects the temperature in the compartment. If required,
change the temperature setting.
• When you first switch on the appliance, to enable suitable cooling or
heating, the appliance should work for 3 hours continuously until it
cools down or heats up to required temperature.
• During this time do not open the door frequently or place a lot of
items inside the appliance.
• If the unit is switched off or unplugged, you must allow at least 5
minutes before restarting or reconnecting the unit.
10
Usage Information
• The unit should be kept away from direct sunlight.
• Remove all transport tapes and foam protection pieces. Clean the
interior of the appliance with a cloth dampened in lukewarm soap and
water. Wipe with clear water and wipe dry.
• Make sure the appliance is turned OFF (model in the OFF position),
place the appliance on flat and even, with good ventilation.
• This appliance is suitable to use in household or inside automobile,
ensure the correct power cord is used.
• To use in household, connect the AC cord (2) to AC input located at the
back of appliance (3) , then connect the power cord to power supply
socket.
• To use in an automobile, connect the DC cord (4) to the DC output at
the back of the appliance (5), then connect the DC plug (6) into
cigarette lighter mounting (7).
Note: Do not use this appliance when engine if off to avoid running
down the car battery.
11
Rear of the appliance
Usage Information
• Plug in the cooler/heater and move the mode switch at rear of the
appliance to Cold or Hot modes. Close the door.
• If you have selected the cold mode then leave the appliance for a
minimum of 3 hours for the correct temperature to be reached before
placing anything inside.
• If you have selected the hot mode leave the appliance for a minimum of
3 hours for the correct temperature to be reached before placing
anything inside.
• After food or drinks have been placed inside the appliance, ensure the
doors is closed fully.
• The maximum capacity is 4L, the appliance can hold a maximum of 6 x
330ml cans or bottle if the shelf and container is removed.
• When you stop using the appliance, turn the mode switch to the OFF
position, then unplug the power cord from appliance and power supply
socket.
• Take out all food or drinks from appliance and wait for the appliance
temperature to rise to room temperature before cleaning and storing.
12
Usage Information
Shelves
• The shelf can be removed to allow for storage of larger items.
• Removing a shelf - Remove all of the items from the shelf that you want
to remove. Lift the shelf upwards and then gently pull the shelf away
from the appliance.
• Replacing a shelf - Place the shelf back into a supporting guide slot and
push it back as far as it will go.
Note:
Whilst the appliance can store larger items, you must make sure that they
do not prevent the door from shutting properly.
13
Cleaning and Maintenance
• Disconnect the appliance from the power supply before cleaning.
• Do not pour water directly over or on the appliance.
• The compartment should be cleaned periodically using a solution of bicarbonate of
soda and lukewarm water.
• Do not use abrasive products, detergents or soaps. After cleaning wipe down with a
damp clean cloth.
• Note: Reconnect to the power after you have dried your hands.
Do not use sharp metal tools as it may damage the appliance.
Do not use an electrical heater, this may cause an electric shock.
Defrosting
The cooler will defrost automatically if frost has started to build up.
Import ant Notes:
• If you do not use your appliance for a long period of time, e.g. when on summer
holidays unplug it. Clean and leave the door open to prevent humidity and bad
odours.
14
Connection to the mains supply
For UK use only – Plug fitting details (where applicable):
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your plug,
proceed as follows:
The GREEN/YELLOW wire is the EARTH and must be connected to the
terminal which is marked with the letter E or by the earth symbol or coloured
GREEN or
GREEN/YELLOW.
The BLUE wire is the NEUTRAL and must be connected to the
terminal marked with the letter N or coloured BLACK. The
BROWN wire is the LIVE wire and must be connected to the
terminal marked with the letter L or coloured RED.
Always ensure that the plug cord grip is fastened correctly.
If a 13A (BS1363) fused plug is used it must be fitted with a
13amp fuse conforming to BS1362 and be BSI or ASTA approved.
15
Troubleshooting
16
Problem
Solution
The appliance doesn't work
Check that the appliance is switched on.
Check that there has not been a power cut.
Check that the plug is not
faulty.
Check that the fuse has not blown.
Check that the voltage is correct for the appliance.
The temperature inside the
appliance is not cold enough
Check that the appliance is not overfilled.
Check that the temperature is set to Cold mode (not Off
or Hot mode)
Check that the appliance is not placed in direct sunlight,
or too near to a heating source.
Check that the ambient temperature is within the
operation limits of the appliance.
Opening the doors frequently will also reduce the
temperature within the appliance.
Check that the door has not been left open
or c
heck that
the door gasket is clean and undamaged.
The temperature within the
appliance is too hot.
Check that the temperature is set to Hot mode (not Cold
mode)
The inner surfaces of the
appliance are wet
Caused by condensation
-
dry the inside of the appliance.
The outer surfaces of the
appliance are wet
Caused by condensation
-
dry the outer of the appliance
carefully.
Unusual noises
Check that the appliance is on a flat, level surface and is
stable. Try adjusting the feet if
not level.
Check the spacing's around the appliance and ensure it is
not touching other items.
Troubleshooting
17
Problem
Solution
Smell/odour
Check that nothing has leaked or any stagnant liquid is at
the bottom of the appliance. Clean if required.
Guarantee
This product is guaranteed for 12 months from the date of the original
purchase. If any defect arises due tofaulty materials or workmanship the faulty
product must be returned to the place of purchase.
Refund or replacement is at the discretion of the retailer.
The following conditions apply:
• The product must be returned to the retailer with the original proof of
purchase.
• The product must be installed and used in accordance with the
instructions contained in this instruction guide and any other instructions
for use which have been supplied.
• It must be used for domestic purposes only and for its intended use.
• This warranty does not cover wear and tear, damage, misuse or
consumable parts.
This does not affect your statutory rights.
18
19
Technical Specification
Model number RH4CLR1001 (B) (SCW) (SCG)
Rated Voltage AC 220-240V~50Hz / DC 12V
Net capacity (litres) 4 litres
Cooling performance 18-22°C below ambient temperature
Heating performance 60°C +/-5°C
Dimensions (CMs): (H)25.2 x (W)17.8 x (D)24.1
Russell Hobbs is a registered trademark used under license from Spectrum
Brands (UK) Ltd. Made under license by G2S Limited, Wigan, WN2 4AY/G2S
(NI) Ltd, Belfast, BT5 5AD.
Russell Hobbs Support: call 0345 208 8750 or visit: mda.russellhobbs.com
The ‘wheelie bin’ symbol is known as the 'Crossed-out wheelie bin Symbol'.
When this symbol is marked on a product/batteries, it means that the
product/batteries should not be disposed of with your general household
waste. Only discard electrical/electronic/battery items in separate collection
schemes, which cater for the recovery and recycling of materials contained
within. Your co-operation is vital to ensure the success of these schemes
and for the protection of the environment. For your nearest disposal facility,
visit www.recycle-more.co.uk or ask in store for details.
SEDEX – Connecting businesses and their global suppliers to share ethical
data and enabling improvement in ethical performance. Visit
www.sedex.org.uk for further information.
We reserve the right, due to possible changes to design, to alter the
instruction manual without prior notice.
Revision 2.3
