Loading ...
Loading ...
Loading ...
TECHNICAL DATA
357XP 359
Engine
Cylinder volume, cu.in/cm 3 3,5/57 3,6/59
Cylinder bore, inch/mm 1,81/46 1,85/47
Stroke, inch/mm 1,34/34 1,34/34
Idle speed, rpm 2 700 2 700
Power, kW/rpm 3,2/9 600 2,9/9 O00
Ignition system
Manufacture
Type of ignition system
Spark plug
Electrode gap, inch/mm
SEM SEM
CD CD
NGK BPMR 7A NGK BPMR 7A
Champion RCJ 7Y Champion RCJ 7Y
0,2/0,5 0,2/0,5
Fuel and lubrication system
Manufacturer Walbro
Carburetor type HDA175
Fuel capacity, US pint/litre 127/0,7
Oil pump capacity at 8500 rpm, ml/min 5-15
Oil capacity, US pint/litre 0,69/0,36
Type of oil pump Automatic
Walbro
HDA175
1,27/0,7
5-15
0,69/0,38
Automatic
Weight
Without bar and chain, Lbs/kg 12,1/5,5
357XPG: 12,3/5,6
Chain/bar
Standard bar length, inches/cm 15"/38
Recommended bar lengths, inches/cm 13-24"/33-61
Usable cutting length, inches/cm 12-23"/31-58
12,1/5,5
359G: 12,3/5,6
15"/38
13-24"/33-61
12-23"/31-58
Chain speed at max. power, m/sec
Pitch, inch/mm
Thickness of drive link, inch/mm
21,4
0,325"/8,25
3/8"/9,52
0,058"/1,5
21,4
0,325"/8,25
3/8"/9,52
0,058"/1,5
Number of teeth on drive sprocket 7
7
Recommended original and replacement
bar and chain combinations
Following is a list of recommended cutting equipment for the
Husqvarna chain saw models 357XP and 359. The combinations of
powerhead, bar and chain have been investigated in accordance with
the kickback and vibration requirements of ANSI B 175.1 - 2000. The
guide bar nose radius is determined by either the maximum number
of teeth in the nose sprocket or the corresponding maximum nose
radius of a solid bar.
The following list is the chain saw manufacturers recommendations.
There may be other combinations available, which will also achieve
kickback reduction.
As we are listing the maximum guide bar nose radius, you may use a
guide bar with smaller nose radius than in our list. For guide bars of
the same length, all sprocket-nose guide bars of the same pitch and
having the same number of of sprocket teeth may be considered to
have equivalent kickback energy. A hard nose bar having the same
length and nose radius as a sprocket-nose bar may be considered to
have equivalent or tess kickback energy than the sprocket-nose bar.
Low kickback saw chain is a chain which has only met the kickback
performance requirements of ANSI B 175.1 safety requirements for
gasoline-powered chain saws when tested on the representative
sample of chain saws below 3.8 cu. in. specified in ANSI B 175.1. We
recommend that you as replacement use the listed chains or "Low
kickback saw chains" which are available at !our dealer.
Guide bar Saw chain
Length Pitch Max nose
inch inch radius
13 0,325" 10T Husqvarna H30 or
15 0,325" 10T Oregon 95VP
16 0,325" 10T
18 0,325" 10T
20 0,325" 10T
13 0,325" 10T Husqvarna H25 or
15 0,325" 10T Oregon 21BP
16 0,325" 10T
18 0,325" 10T
20 0,325" 12T
15 0,325" 10T Oregon 34LG
16 0,325" 10T
18 0,325" 10T
20 0,325" 12T
15 3/8" 11T Husqvarna H42 or
16 3/8" 11T Oregon 73LP/73LG/73V
18 3/8" 11T
20 3/8" 11T
24 3/8" 11T
Note: For the chains above you are free to choose between 0,050"
and 0,058" gauge drive link for the corresponding bar, see table
below.
0,050'/1,3 mm - 20BP 33LG - 72LP 72LG 72V
0,058 /1,5 mm H25 21BP 34LG H42 73LP 73LG 73V
34- English IIIIIIIIIIIIIIIIIIIIIIIII
Loading ...
Loading ...