Loading ...
1
4
2
5
3
6
WHERE TO USE
MODEL PART DIAGRAM
12~18 in 12~18 in
Allow 12 ~ 18 in. of space between TVs, radios, and other electronics
Electromagnetic interference from certain electronics may cause
product malfunction.
Place indoors away from direct sunlight
Direct exposure may cause product malfunction or failure.
Only place on hard, flat surfaces
Flimsy or slanted surfaces may result in abnormal noise and vibrations.
Allow at least 12 ~ 18 in. from walls for maximum air flow
CONTROL PANEL
03
True HEPA Filter
04
PlasmaWave
®
02
Washable AOC™ Carbon FilterPre-Filter
01
4-STAGE AIR PURIFICATION INITIAL OPERATION
Latch
1. Remove the front/rear panel by grasping its upper
edge and gently pulling forward.
- To remove the front/rear panel, release the latch
at the lower edge of the panel.
2. Remove the Pre-Filter, then the plastic bag of
filters behind it.
3. Remove filters from protective plastic bag.
02
01
03
4. Install the filters until they fit securely in place.
03. True HEPA Filter (back)
02. Washable AOC™ Carbon Filter (middle)
01. Pre-Filter (front)
Latch
5. After filters are installed, close the front panel.
6. Insert the power cord into an electrical outlet.
REPLACING FILTERS
Resetting Filter Life:
After replacing your True HEPA Filter, place
the Pre-Filter back in and close the Front
Panel. While the unit is on, use a small, thin
object (such as a paperclip) to hold the Filter
Reset Button for at least 5 seconds until
you hear the beep. After the beep, the Filter
Replacement Indicator will disappear.
Your Winix True HEPA is now reset.
03
(2) Pre-Filter
(2) Washable AOC™
Carbon Filter
(2) True HEPA Filters
Side Vent
Unit
User
Manual
Grill
Rear Panel
Front Panel
Button Control Section
Alexa Setup Guide /
Wi-Fi Setup Guide
01. Auto Mode Indicator
The LED "Auto" light will indicate when Auto Mode is activated.
02. Fan Speed Indicator
Indicates the current fan speed.
03. Sleep Mode Indicator
When Sleep Mode is activated, the Air Quality Indicator LED light is disabled.
Fan speed will automatically set to minimum speed(lower than 'Low') which will be nearly silent.
When Sleep Mode is active, Plasmawave
®
will be disabled, but it can be turned back on.
04. Air Quality Indicator
Color coded LED light indicates one of three levels of Air Quality: Red (poor), Amber (fair), Green (average), and Blue (good).
05. PlasmaWave
®
Indicator
Indicates whether PlasmaWave
®
is enabled or disabled.
06. Wi-Fi Indicator
• Enables or disables the Wi-Fi feature.
• When in the pairing state, the Wi-Fi LED flashes.
07. Filter Replacement Indicator
LED light indicates when it is time to change the filter.
08. Light Sensor
Detects the amount of ambient light in the environment. When in Auto Mode, the Light Sensor detects when to put
the unit into Sleep Mode.
09. Power Button
Turns the unit on or off. During the first 30 seconds of powering up, the Air Quality Indicator will cycle through
Blue, Green, Amber, and Red colors.
• Smart Sensor takes approximately 4 minutes to detect the air quality in the environment before normal operation
begins.
10. Mode Button
Press to cycle through to set the mode of operation (Auto, Sleep). The unit will default to Auto with PlasmaWave
®
enabled when first powered on.
• Auto Mode automatically adjusts fan speeds according to your indoor air quality.
The fan speed will adjust to low when air quality is good, medium when fair, and to high when poor.
11. Sleep Mode Button
When Sleep Mode is activated, the Air Quality Indicator LED light is disabled.
• Fan speed will automatically set to minimum speed (lower than 'Low') which will be nearly silent.
• When Sleep Mode is active, PlasmaWave
®
will be disabled, but it can be turned back on.
12. Plasmawave
®
Button
Press the Plasmawave
®
button when the unit is on to enable or disable this feature. By default, Plasmawave
®
is
enabled whenever the unit is powered on.
"When the unit is running, you may hear a chirping or buzzing sound. The sound is from large particles passing
through Plasmawave
®
, it is normal and does not signify product failure."
13. Wi-Fi Button
• Press for 3 seconds to activate pairing mode.
• When Wi-Fi is paired, press the button to turn Wi-Fi off or back on.
14. Filter Reset Button
After replacing the True HEPA Filter, use a small object such as a clip, to press and hold the Filter Reset Button for
at least 5 seconds until the Filter Replacement Indicator turns off.
CLEANING CARE
Cleaning the Filters:
Use a vacuum cleaner or soft brush to clean the Pre-Filter
• If it is excessively soiled, rinse in room temperature
water.
• Do not use detergent or soap.
• Allow the filter to dry for 24 hours or more before
using.
• Intervals between filter cleaning may vary depending
on the air quality in the environment.
To clean the Washable AOC™ Carbon Filter, remove
from the unit and rinse under lightly running room
temperature water.
• Do not use detergent or soap.
• Allow the filter to dry for 24 hours or mote before
using.
• Do not use hot water over 104ºF.
Cleaning the Exterior & Interior
:
NOTICE
• When cleaning the unit, always unplug the power
cord first and then wait until the unit has cooled
down.
• Never disassemble, repair, or modify this unit
yourself.
• Do not use flammable sprays or liquid detergents.
• Do not allow children to clean or maintain the unit.
• Before cleaning or maintaining, ensure unit is
unplugged.
Wipe with a soft damp cloth using room temperature
water.
• Afterwards, wipe it down with a clean, dry cloth.
Open the front panel and clean the interior with a
vacuum cleaner.
• For optimal performance, clean every 1 - 2 months.
NOTICE
• Do not use benzene, alcohol, or other volatile fluids,
which may cause damage or discoloration.
01. Pre-Filter
Designed to catch larger airborne particles found
indoors.
03. True HEPA Filter
Winix True HEPA captures 99.99%* of airborne allergens
including pollen, dust, smoke, pet dander, and other
ultrafine particles as small as 0.003 microns. *Based on
independent laboratory tests conducted on inanimate
particles as small as 0.003 microns.
02. Washable AOC™ Carbon Filter
Reduces VOCs and household odors from cooking,
pets, and smoke.
04. PlasmaWave
®
Winix PlasmaWave
®
Technology may help to reduce
airborne contaminants*.
*Tested by an independent third-party laboratory.
Visit www.winixamerica.com for more details.
When to Replace Filters
Filter Indicator Light When to Service When to Replace
Pre-Filter
none Clean once every 14 days Permanent
Washable AOC™
Carbon Filter
none Clean once every 3 months
Lasts Approx. 12 months
True HEPA Filter
Can NOT be WASHED
• When the Check Filter Indicator LED is on, it is time to replace the True HEPA Filter and Washable AOC™ Carbon Filter.
• Intervals between filter replacement may vary depending on environment.
* Filter performance may decrease after each wash and depending on contamination level prior to washing.
MAINTENANCE
Loading ...
Loading ...
Loading ...