Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-645-3184,
Monday - Friday, 7:00 a.m. -4:00 p.m., CST .
PACKAGE CONTENTS
1
REVISED 2020-04-08
Stock Part#
PART
DESCRIPTION
QUANTITY
AA
CC
Fixture Body
B
A
C
AA
BB
CC
A
B
Crossbar Assembly
1 pc
3 pcs
2 pcs
Wire Connector
Outlet Box Screw
3 pcs
1 pc
3 pcs
3 pcs
D
N/A
BB
Vintage Bulb
SKU NUMBER: 351-8649
FLUSH MOUNT CEILING FIXTURE
MODEL NUMBER: MND4244E
Shade
C
D
Cap
E
E
3 pcs
Socket Collar
G12835SH
N/A
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the
product.
WARNING:
● Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing
fuse (or switching off circuit breaker).
● Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit
wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation,
which could cause serious injury or death from electric shock
CAUTION:
● All electrical connections must be in agreement with local codes, ordinances or the national electric
code (NEC). Contact your municipal building department to learn about your local codes, permits
and/or inspections.
● Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a
qualified electrician before installation.
● Do not connect this fixture to an electrical system that does not provide a means for equipment
grounding. Never use a fixture in a two-wire system that is not grounded. If you are not sure your
lighting system has a grounding means, do not attempt to install this fixture. Contact a qualified,
licensed electrician for information with regards to proper grounding methods as required by the local
electrical code in your area.
● If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct
type and electrical rating required.
Before beginning assembly, installation or operation of product, make sure all parts are present. Compare
parts with package contents list and diagram on previous page. If any part is missing or damaged, do not
attempt to assemble, install or operate the product. Contact customer service for replacement parts.
Light Source: (3) 60W Type-S medium base vintage-style bulb, Alternate (3) LED bulb.
Tools Required for Assembly (not included): Screwdriver, Phillips Screwdriver, Pliers, Electrical Tape,
Safety Glasses, Ladder.
PREPARATION
2
HARDWARE CONTENTS Note: Hardware not shown actual size.
Crossbar
x 1
Wire Connector
x 3
AA BB CC
Outlet Box Screw
x 2
ASSEMBLY INSTRUCTIONS
3
Outlet Box Screw
Outlet Box
STEP 2:
a. Remove lock ball and Hex Nut from crossbar
assembly (AA).
b. Fit ceiling canopy (A) over the nipple on crossbar
assembly and secure with lock ball.
Note: The ceiling canopy should be snug against
the ceiling and the lock ball.
Ÿ If not, adjust the length of the nipple on the crossbar
assembly by unscrewing the preassembled hex
nut.
Ÿ Then, screw the nipple in or out of the crossbar
until the desired length is achieved.
Ÿ Once the ceiling canopy is secure, remove the lock
ball and ceiling canopy and proceed to Step 3.
lock ball
Hex Nut
Hex Nut and
Lock Washer
STEP 1:
a. Secure the crossbar (AA) to the outlet box (not
included) with outlet box screws. Tighten until
snug.
Note: The preassembled mounting nipple on the
crossbar should protrude outward.
AA
A
AA
STEP 3:
a. The lanyard is provided as a means to support the
fixture from the junction box while connecting the
electrical wires. This enables the fixture to hang
from the junction box and your hands are free to
make the wire connections.
b. Turn the button stop so it may be inserted into the
crossbar slot. Make sure the button stop is
completely inside the crossbar.
c. Slowly release the fixture to make sure it is
supported by the button stop.
d. Proceed to Step 4. Once wiring is complete, the
lanyard will push into the junction box when the
Ceiling Canopy is Attached to the ceiling.
Crossbar Assembly
Button Stop
Lanyard
Slot
WHITE
BLACK (OR RED) WIRE
WHITE
BLACK
FROM SUPPLY
FROM SUPPLY
FROM FIXTURE
FROM FIXTURE
STEP 4:
* Use Wire Connectors (supplied) to connect the
wires.
a) Ground Wire:
1. Wrap supply ground wire around green ground
screw on mounting bracket, no less than 2 inches
from the end of the wire. Tighten ground screw.
2. Connect fixture ground wire to supply ground
wire with wire connector.
b) Supply Wire:
1. Connect the supply white wire to the white
fixture supply wire with wire connector.
2. Connect the supply black (or red) wire to the
black fixture supply wire with wire connector.
3. Wrap each connection with approved electrical
tape and carefully stuff all of the connected wires
into the outlet box.
GROUND WIRE
GROUND WIRE
FROM SUPPLY
FROM FIXTURE
GREEN GROUND SCREW
ASSEMBLY INSTRUCTIONS
4
STEP 5:
A. Re-attach the ceiling canopy to the crossbar
assembly.
b. Secure with the previously removed Hex Nut.
c. Then, attached the lock ball over the ceiling
canopy.
Crossbar Assembly
lock ball
Hex Nut
STEP 6:
This fixture was designed to be used with or without
glass
Option 1: Without Glass
a. Install correct bulbs referring to fixture markings
and/or labels for maximum wattage.
Option 2: With Glass
a. Remove Socket Collar (E) from Fixture Body (A).
b. Place Cap (B) over the Socket, secure by
threading Socket Collar (E) onto Socket. Hand
tighten until sung.
c. Install correct bulbs referring to fixture markings
and/or labels for maximum wattage.
d. Place the Shade (C) over the bulb and thread it
onto the Cap (B) properly.
Your installation is completed now. Restore
electricity. Retain this sheet for future reference.
Option 2
Option 1
B
D
CARE AND MAINTENANCE
TROUBLESHOOTING
1) The light does not come on at all:
a) Make sure the wall switch and circuit breaker are on.
b) Make sure the wiring is correct.
2) Fuse blows or circuit trips when light is turned on.
a) Check for crossed wires, ensure wiring is correct.
If unable to fix any of the above issues, please consult a certified electrician.
• To clean, turn off and wipe with a damp, non-abrasive cloth.
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-645-3184,
Monday - Friday, 7:00 a.m. -4:00 p.m., CST .
E
D
C
