Loading ...
Loading ...
Loading ...
7
• This washer is heavy. Two or more people are required when
moving and unpacking the washer. Failure to do so may result in
damage to property or serious bodily harm.
• Store and install the washer where it will not be exposed to
temperatures below freezing or exposed to outdoor weather
conditions. Failure to follow this warning can cause serious injury, re,
electric shock, or death.
• Properly ground the washer to conform with all electric governing
codes and ordinances. Failure to follow this warning can cause serious
injury, re, electric shock, or death.
• To reduce the risk of electric shock, do not install the washer in
humid spaces. Failure to follow this warning can cause serious injury,
re, electric shock, or death.
• To ensure proper air ow, do not block the large opening on the
bottom of the washer with carpeting or other materials.
• Do not remove ground prong. Do not use an adapter or extension
cord. Plug into a grounded 3-prong outlet. Failure to follow this
warning can cause serious injury, re, electric shock, or death.
• Certain internal parts are intentionally not grounded and may present
a risk of electric shock only during servicing. Service personnel - Do
not contact the following parts while the appliance is energized:
pump, valve, motor, control board.
NOTE: Installing the washer in a humid space, or installing or storing the
washer where it will be exposed to the weather or freezing temperatures,
may result in rust or other damage that is not covered by the product
warranty.
Power Outlet
• The power outlet must be within 60 in. (1.5 m) of either
side of the washer.
• The appliance and outlet must be positioned so that
the plug is easily accessible.
• Do not overload the outlet with more than one appliance.
• The outlet must be grounded in accordance with
current wiring electric codes and regulations.
• Time-delay fuse or circuit breaker is recommended.
NOTE: It is the personal responsibility and obligation of
the product owner to have a proper outlet installed by a
qualied service technician.
• To minimize noise and vibration, the washer MUST be
installed on a solidly constructed oor. See the NOTE at right.
• Allowable slope under the entire washer is a maximum
1 in. dierence from side to side or from front to back.
• Installing on carpeting and soft tile surfaces is not
recommended.
• Never install the washer on a platform or weakly
supported structure.
NOTE: The oor must be strong and rigid enough to
support the weight of the washer, when fully loaded,
without exing or bouncing. If your oor has too much ex,
reinforce it to make it more rigid.
A oor that is adequate for a top-loading washer may
not be rigid enough for a front loading washer, due to the
dierence in the spin speed and direction. If the oor is not
solid, your washer may vibrate and you may hear and feel
the vibration throughout your house.
Description Front-Loading Washer
Electrical Requirements 120 VAC, 60 Hz
Max. Water Pressure 20 - 120 psi (138 - 827 kPa)
Dimensions 27”(W) X 30 ¼”(D) X 39”(H), 55” (D with door open)
70 cm(W) X 77 cm(D) X 99 cm(H), 139.6 cm (D with door open)
Net Weight 220 lbs (100 kg)
Max. Spin Speed 1,300 RPM
WARNING
To ensure sucient clearance for water lines and airow,
allow minimum clearances of at least 1 in. (2.5 cm) at the
sides and 4 in. (10 cm) behind the unit. Be sure to allow
for wall, door, or oor moldings that may increase the
required clearances.
Allow at least 24
3
/4 in. (62.6 cm) in front of
the washer to open the door.
KEY DIMENSIONS AND SPECIFICATIONS
CHOOSE THE PROPER LOCATION
FLOORING
CLEARANCES
INSTALLATION REQUIREMENTS
1 in.
(2.5 cm)
1 in.
(2.5 cm)
27 in.
(70 cm)
4 in.
(10 cm)
24
3
/4 in.
(62.6 cm)
31
1
/4 in.
(77 cm)
55 in.
(139.6 cm)
1-MFL68005553-영.indd 7 2018. 8. 29. 오전 10:42
Loading ...
Loading ...
Loading ...