Loading ...
10
kit Part numbers and Cut out dimensions table
Refrigerator Model
Kit Part Numbers Cut Out Dimensions
Brushed
Stainless
Plus
Joiner
Kit
Width
A
Depth
B*
Height
C**
1 x 635
(25")
LH
807
635
1790
23980 807mm
31 ⁄”
700mm
27 /”
1790mm
70 /”
1 x 635
(25")
RH
807
635
1790
23981 807mm
31 ⁄”
700mm
27 /”
1790mm
70 /”
2 x 635
(25")
1467
635
635
1790
23982 819264 1467mm
57 /”
700mm
27 /”
1790mm
70 /”
1 x 680
(26 /")
LH
852
680
1790
23983 852mm
33 ⁄”
700mm
27 /”
1790mm
70 /”
1 x 680
(26 /")
RH
852
680
1790
23984 852mm
33 ⁄”
700mm
27 /”
1790mm
70 /”
2 x 680
(26 /")
1557
680 680
1790
23985 819264 1557mm
61 /”
700mm
27 /”
1790mm
70 /”
9
moVe into CaVity
If installing two refrigerators/
freezers side by side a joiner
kit is required. Refer to these
instructions and fit joiner kit
before pushing refrigerator into
place, see diagram6.
Plug refrigerator into electrical
socket, run water connection
to refrigerator if required
(Ice&Water models only).
Gently install refrigerator into
cabinetry making sure it is
centred within the surroundtrim.
The front of the refrigerator
door should be flush with the
front of the cabinetry to obtain
anintegratedlook.
Ensure the front leveling feet are
adjusted to take the load of the
fridge and keep it in place.
Optional
Diagram 6
8
trim installation
The bottom trim is designed to cover the front edge of the
floor base panel of the cabinet. This trim can be installed
on a raised toe kick (diagram 1a) or toe kick below the
refrigerator (diagram 1b)
Remembering that if this trim is to be used with the
refrigerator at floor level the cut out dimensions will need
to have 16mm (/") added to its height to allow for the
bottom trim to be fitted. Note this trim is optional on this
type ofinstallation. If used with a raised toe kick the 16mm
packer should be part of the base (diagram5). Therefore
16mm is not required to be added to the height dimension.
1. If used place the 16mm (/") piece of plywood or
with bottom trim fitted into the cavity (diagram 5 or 6).
Note the piece should be the same size as the base of
the cavity.
2. Remove protective coating film from surround trim.
3. To install the surrounds, first clip in the top surround.
Ensure the locator strips at the rear of the top brackets clip
into the rear of the top trim.
4. Clip both side trims into place starting from the front
cabinet edge.
16mm (/ inch)
plywood or MDF
board insert
Part of base
Diagram 5
Refrigerator Model
Kit Part Numbers Cut Out Dimensions
Brushed
Stainless
Plus
Joiner
Kit
Width
A
Depth
B*
Height
C**
1 x 790
(31 /")
LH
962
790
1790
23986 962mm
37 /”
700mm
27 /”
1790mm
70 /”
1 x 790
(31 /")
RH
962
790
1790
23987 962mm
37 /”
700mm
27 /”
1790mm
70 /”
2 x 790
(31 /")
1777
790
790
1790
23988 819264 1777mm
70”
700mm
27 /”
1790mm
70 /”
1 x 900
(35 /")
(French door
model)
1072
900
1875
23989 1072mm
42 ¼”
700mm
27 /”
1875mm
73 /”
1 x 790
(31 /")
(French door
model)
962
790
1790
23990 962mm
37 /”
700mm
27 /”
1790mm
70 /”
* Depth is a minimum requirement
** Height is without 16mm MDF packer
*** For refrigerators / freezers where the hinge is not concealed
by the door refer to spare parts for the correct kit number.
820413 D should list non concealed number kit.
Before you call for service or assistance ...
Check the things you can do yourself. Refer to the installation instructions, your User Guide – inparticular
the troubleshooting section and check that:
1
your product is correctly installed.
2
you are familiar with its normal operation.
If after checking these points you still need assistance or parts, use the link at
www.fisherpaykel.com for regional service providers.
839254 A NZ AU GB AE HK SG IE US CA EU CN IN 09.13
Concealed Hinge Non Concealed Hinge