Loading ...
Loading ...
Loading ...
Controls: See Fig. 4
Icon Display Function Description
A -
Power /
Standby
Press once to turn the product ‘ON’.
Press a second time to put the product into ‘STANDBY’
(When returning from ‘STANDBY’ mode the product will return to previous settings unless the product
has been unplugged, in which case it will reset to factory settings)
B
Sleep
Timer
Press multiple times to change the ‘SLEEP TIMER’ in 0.5 hr increments from 0.5 hr to 8.0 hr before turning
off. The remaining time on the ‘SLEEP TIMER’ displays. (This icon is Green in Colour)
C
Flame Effect
‘FLAME EFFECT’ button cycles the unit sequentially through the 4 setting, LOW FLAME, HIGH FLAME,
DEMO MODE and OFF.
f1
Low
Flame
This setting will run the ame effect at a low brighness level. (The display will show F1)
f2
High
Flame
This setting will run the ame effect at a high brighness level. (The display will show F2)
fp
Demo
Mode
This setting will slowly pulse the ame effect between low and high brightness. (The display will show
FP)
-
Off
This will turn the ame effect off. If the heater is running, the display will activate and remain active to
read the set temperature and show if the product is on LOW HEAT/ HIGH HEAT/COOL BLOW.
D
Log Effect
‘LOG EFFECT’ button cycles the unit sequentially through the 3 settings, ‘PULSING LOGS, STATIC LOGS
and OFF.
Lp
Pulsing
Logs
This setting will make the logs pulse. (The display will show FP)
LS
Static
Logs
This setting will make the logs stay lit. (The display will show FS)
-
Off
This setting will turn the logs off.
E
-
On / Off
This button cycles the top light ‘On’ and ‘Off’.
F
Heat
‘HEAT’ button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT, COOL BLOW
and OFF. The heat setting will be indicated by an icon in the oating display see Fig.1.
When the ame effect is ‘ON’ the oating display will turn off after 5 seconds, however if the heater is
being used independently of the ame effect, the low heat or high heat icon will appear continuously
in the oating display.
Low Heat
This setting will run the heater at ‘LOW HEAT’ this setting will be indicated by the ‘LOW HEAT’ icon
and the letters ‘LO’ appearing in the display.
(This icon is Orange in Colour)
High
Heat
This icon in the oating display indicates ‘HIGH HEAT’ this setting will be indicated by the ‘HIGH HEAT’
icon and the letters ‘HI’ appearing in the display.
(This icon is Red in Colour)
Cool
Blow
This icon in the oating display indicates ‘COOL BLOW’ this setting will be indicated by the ‘COOL
BLOW’ icon and the letters ‘CB’ appearing in the display.
(This icon is Blue in Colour)
- Off
This switches the heater and blower ‘OFF’, no icon will be displayed in the oating display. Note the
blower will run for 10-20 seconds after being turned off this is to ensure the product cools down safely.
G -
Temp
Down
Press multiple times to lower the heater temperature in 1
0
C increments. The lowest temperature that
can be set is 5
0
C.
Note: Once you stop at your desired temperature this will flash 3 times, then the display will show the
room temperature as detected by the product. If the set temperature is lower than the detected
room temperature the heater will not activate.
H - Temp Up
Press multiple times to increase the heater temperature in 1
0
C increments. The highest temperature
that can be set is 37
0
C.
Note: Once you stop at your desired temperature this will flash 3 times, then the display will show the
room temperature as detected by the product. If the set temperature is lower than the detected
room temperature the heater will not activate.
User Modes:
Mode Name /Discription Action (Actions cannot be input by remote control)
Change Celsius (
0
C) to Fahrenheit (
0
F)
Press both Temp+ ( ) and Temp– ( ) on the unit and hold until a beep is heard
and display flashes. (To revert back to Celsius repeat this action)
Disable/Enable Heat Options
Hold both Heat ( ) and Flame ( ), on the unit, for 2 seconds, when the heater has
been disabled the display will read “--” and beep. To enble heat repeat this action.
Loading ...
Loading ...
Loading ...