SL1466 User Manual

Loading ...

• 5 •

USING THE LED LIGHT

Choose from Normal, SOS and Emergency Flash modes.

1. Press the

button on the side of the unit for 2 seconds to turn on the LED light. The icon will show on the LCD screen.

2. Press the

button again for SOS mode.

3. Press the

button once more for emergency ashing.

4. Long press the

button for 2 seconds to turn off the LED light.

USING THE AC POWER OUTLETS

The SL1466 is equipped with a 500W pure sine wave inverter, which produces power for all electronic devices and appliances.

It is important to know the continuous wattage of the device you plan to use with the AC outlets. The unit must be used with devices drawing 500 watts or less.

Devices such as fans or electric motors require additional power to start (commonly known as the “starting” or “peak” power). The generator can supply a momentary surge

in wattage of as high as 1000W for less than 1/10 of a second; however even devices rated less than the maximum 500 watts can exceed the inverter’s surge capability

and cause an automatic overload shutdown.

Do not use the inverter with a product that draws a higher wattage than the inverter can provide, as this may cause erratic operation.

CAUTION: Always run a test to establish whether the inverter will operate a particular piece of equipment or device.

In the event of a power overload (noted with a ashing

Warning icon), the inverter is designed to automatically shut down. This safety feature prevents damaging the

inverter while testing devices and equipment within the 500-watt range.

If powering more than one device, start one device at a time to avoid a power surge and/or inverter overload. The surge load of each device should not exceed the

inverter’s Continuous Operation wattage rate.

You can use an extension cord from the inverter to the device without signicantly decreasing the power being generated by the inverter. For best operating results, the

extension cord should be 16 AWG (1.31 mm

)

or larger and no longer than 50 feet.

WARNING! RISK OF ELECTRIC SHOCK.

Incorrect operation of your inverter may result in damage and personal injury. The inverter output is 110V AC and can shock or electrocute the same as any ordinary

household AC wall outlet.

NOTE: The maximum continuous load is 500 watts. Do not use the AC outlets with a product that draws more than 500 watts, as this may cause erratic operation.

CAUTION:

• Do not connect an AC power source to the 110V AC outlets.

• Do not connect the unit’s AC power cord to its 110V AC outlets.

NOTE: Do not power an AC device while charging the internal battery.

1. Connect your AC-powered devices or small household appliances to one or more of the unit’s two AC outlets.

NOTE: Make sure the device to be powered is OFF before inserting the plug into the AC power outlet.

2. Press the AC Power button. The

AC Output icon will show on the display, to conrm that the unit is on and ready to provide AC power. The

Power Output indicator

will also show on the display.

NOTE: Extended operation of an AC device may result in excessive battery drain.

3. Recharge the unit when the battery level is below 40%.

ESTIMATED RUN-TIMES

APPLIANCE TYPE ESTIMATED RUN TIME CHARGES

Jig Saw 2.4 hours —

Projector 7 hours —

12V Heated blanket 13 hours —

12V Cooler 15 hours —

Mini Fridge 20 hours —

Television 21 hours —

Drone 22 hours 103

Fan 26 hours —

Router 54 hours —

Table lamp 59 hours —

Laptop 106 hours 12

LED lights 150 hours —

Camera 190 hours 99

Radio 222 hours —

Tablet 247 hours 15

Speaker 680 hours 44

Smartphone 765 hours 49

NOTE: Actual time may vary. Times are based on the internal battery being fully charged.

7. MAINTENANCE AND CARE

• Recharge the unit when the battery level is below 40%.

• Never completely discharge the internal battery.

Loading ...

User Manual - Page 5