Loading ...
Loading ...
Loading ...
OPERATION
,11, i1,11 ,ill! I,H,, i, ,i,
TO START ENGINE
o To start a cold engine, push primer five (5) times
before trying to start. Use a firm push° This step is not
usually necessary when starting an engine which has
already run for a few minutes.,
o Push engine speed control lever to HIGH (+._) posi-
tion,
o Hold operator presence control bar down to the
handle and pull starter' handle quickly. DO NOT
allow starter rope to snap back.
o To STOP engine, release operator presence control
bar+
NOTE: in cooler weather' it may be necessary to repeat
priming steps° In warmer weatherover priming maycause
flooding and engine will not starL If you do flood engine,
wait a few minutes before attempting to start and DO NOT
repeat priming steps.
MOWING TiPS
o Under certain conditions, such as very tall grass, it
may be necessary to raise the height of cut to reduce
pushing effort and to keep from overloading the en-
gine and leaving clumps of grass clippings.
° For extremely heavy cutting, reduce the width of cut
and raise the rear of the lawn mower housing one (1)
wheel adjuster setting higher than the front for better
discharge of grass+
o For better grass bagging and most cutting conditions,
the engine speed should be set in the '"HIGH" (FAST)
(<r_) position,.
o When using a rear discharge lawn mower in moist,
heavy grass, clumps of cut grass may not enter the
grass catcher+ Reduce ground speed (pushing speed)
and/or run the lawn mower over the area a second
time.
• If a trail of grass clippings is left on the right side of a
rear discharge lawn mower, mow in a clockwise
direction with a small overlap to collect the clippings
on the next pass,
o Keep top of engine around starter clear and clean of
grass clippings and chaff. This will help engine air
flow and extend engine life+
. Pores in cloth grass catchers can become filled with
dirt and dust with use and catchers will collect less
grass° To prevent this, regularly hose catchers off
with water and let dry before using.
MAX 113
FIG. 10
MULCHING MOWING TiPS
IMPORTANT: FOR BEST PERFORMANCE, KEEP
MOWER HOUSING FREE OF BUILT-UP GRASS AND
TRASH, CLEAN UNDERSIDE OF MOWER HOUSING
AFTER EACH USE. SEE "CLEANING" IN CUSTOMER
RESPONSIBILITIES SECTION OF THIS MANUAL.
o The special mulching blade will recut the grass clip-
pings many times and reduce them in size so that as
they fall onto the lawn they will disperse into the grass
and not be noticed. Also, the mulched grass will
biodegrade quickly to provide nutrients for the lawn
Always mulch with your highest engine (blade) speed
as this will provide the best recutting action of the
blades._
- Avoid cutting your lawn when it is wet,, Wet grass
tends to form clumps and interferes with the mulching
action The best time to mow your lawn is the early
afternoon+ At this time the grass has dried and the
newly cut area wiU not be exposed to the direct sun.
o For best results, adjust the lawn mower cutting height
so that the tawn mower cuts off only the top one-third
of the grass blades (See Fig, 10)+ If the lawn is
overgrown itwill be necessary to raise the height of cut
to reduce pushing effort and to keep from overloading
the engine and leaving clumps of mulched grass. For'
extremely heavy mulching, reduce your width of cut,
mow slowly and raise the rear of the lawn mower one
wheel adjuster setting higher than the fronL
° Certain types of grass and grass conditions may
require that an area be mulched a second time to
completely hide the clippings+ When doing a second
cut, mow across or perpendicular to the first cut path.
o Changeyourcutting pattern from weektoweek. Mow
north to south one week then change to east to west
the next week. This will help prevent matting and
graining of the lawn.
10
Loading ...
Loading ...
Loading ...