Loading ...
@
) CHECK INSTALLATION DIMENSIONS
A: Disposer Height
B: Distance from bottom of sink
bowl to centerline of discharge
outlet. (Add 1/2" when stainless
steel sink is used.)
C: Distance from centerline of
the discharge outlet to end
of discharge tube.
D: Disposer Width
E: Distance from disposer vertical
centerline to centerline of
P-trap connection.
B
i
,',,--I__I
F: Centerline of disposer discharge to centerline at waste pipe entering wall
(Dimension "F" must be greater than 1/4" to prevent standing water in disposer.)
i f replacing an existing disposer, skip ahead to Instruction 6. I
If this is a first time installation, continue with Instruction 2.
I
O DISCONNECT SINK DRAIN
1. Loosen nut (A) at top of "P-trap" with pipe wrench (see Figure 2-1).
2. Loosen nut (B) at top of extension pipe. Remove extension pipe.
3. Loosen nut (C) at base of sink flange. (If nut is corroded or too tight, apply
penetrating lubricant,)
4. Push sink flange up through sink hole and remove it (see Figure 2-2).
5. Clean sink flange area of any putty or other debris.
O DISASSEMBLE NEW DISPOSER
MOUNTING ASSEMBLY
1. insert wrenchette (or screwdriver) into one mounting lug and hold lower mount-
ing ring securely with one hand (see Figure 3-1). With your other hand, turn
mounting assembly counterclockwise to remove mounting assembly from lower
mounting ring.
2, Turn mounting assembly over (see Figure 3-2) and loosen three mounting
screws (A) until you can access snap ring (B).
3. Use screwdriver to pry snap ring off of sink flange. Mounting assembly will
now come apart.
O INSTALL FLANGE IN SINK HOLE
1. Roll 1/4 pound (4 oz.) of non-hardening plumber's putty to make 3/4" thick rope
to seal around sink flange.
2. Apply putty evenly around sink hole (see Figure 4-1).
3. Press sink flange slowly but firmly into sink drain hole to seat evenly on putty
(see Figure 4-2). Use screwdriver or putty knife to scrape all putty from edge
of sink hole.
Model A B C D E
601016012 11 3/8" 6" 4' 6 5/16" 5"
6011/6013 12 5/8" 6" 4" 6 5/16" 5'
60552 12 5/80 6" 4" 7 1/4" 5_
60581/60554 12 3/4" 6 11/16 = 4" 8 1/2" 6 3/4m
60691/60556 12 3/4 = 6 1t/16 m 4" 8 1/2" 5 3/4'
60559* 15 7/8 = 9 7/16" 4" 7 1/2" 5 3/4'
60571/60562 12 5/8' 6" 4= 7 1/4" 5"
60572/60563 12 5/8" 6" 4' 7 1/4= 5"
60793 12 3/4" 6 11/16 = 4" 8 1/4" 5 3/4"
Indicates Batch Feed Model
9
"P-Trap"
2-1
/
2-2
4-1
O ATTACH UPPER MOUNTING ASSEMBLYTO SINK FLANGE
You may wish to place a weighted object in the sink to hold the sink flange in place. (Place a towel
under object in sink to prevent scratching.) Reference Figure 5-1 for part identification.
1. Working from under sink, slip fiber gasket and 4. Tighten three mounting screws up to sink
metal backup ring over sink flange.
2. Holding fiber gasket and backup ring in place,
slip mounting ring over sink flange so it seats
against backup ring.
3. With fiber gasket, backup ring, and mounting
ring tight to sink bottom, slide snap ring onto
sink flange until it pops into groove on flange*.
until mounting assembly is seated tightly
and evenly against sink.
* Placing a thick, wide rubber band around
the sink flange (above the snap ring
groove) may help hold parts in place while
installing snap ring. (Remember to remove
rubber band after snap ring is installed.)
4-2
- O--
SinkFlange
FiberGasket_ O
BackupRing-- _)
MountingRing __
Screws(3)_ BiB
SnapRing -- O
I f you are replacing an existing disposer, go to Instruction 6. If this is a first time installation,
skip ahead to Instruction 7.
5-1
Loading ...
Loading ...
Loading ...