Loading ...
Loading ...
Loading ...
TROUBLESHOOTING
PROBLEM
Rider Will Not Move Or
Loss Of Traction
Blade(s) Not Cutting
Cutting Grass
Improperly
Poor Grass Discharge
Battery Will Not Charge
Oil Leaking
PROBABLE CAUSE
1. Joystick in the neutral "N" position.
2. Roll release lever is in "ROLL" position.
3. Low transmission hydraulic oil level.
4. Parking Brake engaged.
5. Traction drive belt requires replacement
CORRECTIVE ACTION
1. Place joystick in desired speed position.
2. Move roll release lever to the engaged position.
3. Contact authorized SNAPPER dealer.
4. Move parking brake to disengaged position..
5. Replace traction drive belt.
1. Blade engagement switch in the "OFF" position. 1.
2. Clutch belt slipping. 2.
3. Mower belt slipping. 3.
4. Electric clutch not functioning. 4.
1. Uneven tire pressure. 1.
2. Cutting height too low or high.
3. Engine speed too slow.
4. Forward speed too fast.
5. Terraced cut, side to side.
6. Excessive deck pitch, front to rear.
7. Cutting blade(s) dull or damaged.
Move blade switch to the "ON" position.
Replace clutch belt.
Replace mower belt.
Contact authorized SNAPPER dealer.
Bring to proper pressure.
2. Adjust cutting height.
3. Move engine speed control to "FAST" position.
4. Move joystick to a slower speed.
5. Adjust side to side level
6. Adjust front to rear pitch.
7. Sharpen cutting edges or replace blade(s).
8. Blade belt slipping. 8. Replace blade belt.
9. Check electric clutch. 9. Adjust to proper specifications. (33" Deck Only)
10. Check clutch belt. 10. Replace clutch belt.
1. Engine speed too slow. 1. Move engine speed control to "FAST" position.
2. Forward speed too fast. 2. Move joystick to a slower speed.
3. Grass is wet. 3.
4. Excessively worn or damaged blade(s). 4.
5. Build up of grass clippings and debris under deck. 5.
6. Improper blade(s) installed on deck. 6.
7. Blade(s) installed improperly on deck. 7.
1. Poor cable connections. 1.
2. Bad battery cell(s) 2.
3. Faulty alternator. 3.
1. Leaking hose fittings, clamps or reservoir. 1.
Mow when grass is dry.
Service mower blade(s)
Clean deck.
Install proper SNAPPER blades.
Install blades properly.
Clean cables and battery terminals.
Replace with new battery.
Contact engine manufacturer's dealer.
Verify fittings and hose clamps are tight.
4.6. MAINTENANCE/REPLACEM ENT PARTS
MAINTENANCE/REPLACEM ENT PARTS
Engine Speed Control Cable (Kohler 15 HP)
En_line Speed Control Cable IKohler 18 HP)
Choke Control Cable (Kohler 15 HP)
Choke Control Cable (Kohler 18 HP)
42" Cutter Deck Blade (2 Blades Required)
48" Cutter Deck Blade (3 Blades Recluired I
42" Cutter Deck Belt (Electric Clutch to Cutting Deck)
48" Cutter Deck Belt IElectric Clutch to Cuttin_l Deck)
Wheel Drive Belt (Engine to Hydro Transaxle)
Wheel Drive Belt (En_line to Hydro Transaxle) 148" Deck Only)
Mower Drive Belt (Engine to Electric Clutch)
Mower Drive Belt (En_line to Electric Clutch) 148" Deck Only)
Parts Manual for Yard Cruiser Series 1 & 2
3-6506
4-2992
2-4185
2-4185
2-6691
2-9247
3-6585
4-2997
4-1823
4-1829
2-9117
4-6997
06109
25
Loading ...
Loading ...
Loading ...