Loading ...
Loading ...
Loading ...
Turning Grill Off
• Turn all knobs to OFF position. Turn LP cylinder off by turning
Igniter Check
• Turn gas off at LP cylinder. Press and hold electronic igniter
button. "Clicking" should be heard and spark seen each time
between collector box or burner and electrode. See
"Troubleshooting" if no click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before checking valves.
Knobs lock in OFF position. To check valves, first push in knobs and
release, knobs should spring back. If knobs do not spring back,
replace valve assembly before using grill. Turn knobs to LOW
position then turn back to OFF position. Valves should turn smoothly.
Hose Check
• Before each use, check to see if hoses are cut or worn. Replace
damaged hoses before using grill. Use only valve/hose/regulator as
specified in the parts list of this Use & Care Guide.
Burner Flame Check
• Remove cooking grates and heat diffusers. Light burners, turn
knobs from HI to LO. You should see a smaller flame in
LO position than seen on HI. Perform burner flame check
on sideburner, also. Always check flame prior to each use. If
only low flame is seen refer to "Sudden flame drop or low flame" in
the Troubleshooting Section.
WARNING
Match Lighting
▲Do not lean over grill while lighting.
1. Open lid during lighting.
2. Place match into match holder (hanging on right back leg).
Light match, place into lighting hole on left side of firebox.
3. Turn right knob to HI position. Be sure burner lights and stay lit.
4. Light other burners follow with step 3.
Sideburner Match Lighting
1. Open sideburner lid. Turn on gas at LP cylinder.
2. Place lit match near burner.
3. Turn sideburner knob to HI. Be sure burner lights and stays lit.
Turn controls and gas source or tank OFF when not
in use.
CAUTION
HIGH
LOW
If ignition does not occur in 5 seconds, turn the
burner controls OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could ignite with risk of injury.
.
146.34611411 • 9
HI
LO
Cast Iron Grate Seasoning (if applicable)
First Use – Before first use, season cast iron grates as follows: Rinse
cast iron grates with hot water. Do not use soap. Dry grates
thoroughly with a cloth towel. Coat grates with vegetable oil or
non-stick cooking spray. Place grates in grill. Start grill and slowly
raise temperature to 350° - 400° F. Heat grates for one hour. Turn
off grill and allow grates to cool completely before using to cook.
Cleaning – Do not use soap when cleaning grates. Clean grates with
a stiff brush and hot water. Dry grates thoroughly with a cloth towel.
Re-seasoning – Re-season grates when rust spots appear on grate
surface. When re-seasoning grates, soap may be used with hot
water to clean grates. After cleaning, dry grates thoroughly with a
cloth towel. Coat grates with vegetable oil or non-stick cooking
spray. Place grates in grill. Start grill and slowly raise temperature
to 350° - 400° F. Heat grates for one hour. Turn off grill and allow
grates to cool completely before using again.
General Grill Cleaning
• Do not mistake brown or black accumulation of drip and smoke
for paint. Interiors of gas grills are not painted at the factory
(and
should never be painted). Apply a strong solution of detergent
and water or use a grill cleaner with scrub brush on insides of
grill lid and bottom. Rinse and allow to completely air dry.
Do not
apply a caustic grill/oven cleaner to painted surfaces.
•
Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use nonabrasive scouring powder
for stubborn stains.
Loading ...
Loading ...
Loading ...