Loading ...
Loading ...
Loading ...
4
1
Touch the Power button once. The unit will automatically be in
Cooling and MoneySaver
®
mode with the temperature
set at 75
°
F (24°C)
and the fan speed at F1, the sleep setting.
To set mode of operation
3
The unit will automatically be in Cool mode. To go to the next
mode of operation, press the System button.
In order to run the fan by itself, do the following:
4
Continuing from Cool
mode, press the System button
once
To adjust temperature
(The unit needs to be in Cool or MoneySaver
®
or Heat mode.)
6
COOLER – Touch the
button to lower the room air temperature.
7
WARMER – Touch the
button to raise the room air temperature.
To adjust fan speed
8
Touch the Fan Speed b
utton
to se
e
the current setting.
Touch
it again to change speed. "F1" is the lowest setting
(SLEEP SETTING / LOW), "F2" is MEDIUM, "F3" is HIGH and
"SF" is SmartFan. In SmartFan mode, the fan will automatically
select the fan speed needed to satisfy your desire set point
NOTE: SMART FAN DOES NOT OPERATE IN
CONJUNCTION WITH THE FAN ONLY MODE.
To set the hour clock
9 Touch the Set Hour button to see the current setting. The
Use the buttons to change the settings. BE SURE
number that is displayed is the approximate time (hour only).
and
TO SET A.M. AND P.M. ACCORDINGLY. (P.M. is indicated by
a red light in the upper left corner of the display).
To set the timer
NOTE: Set the HOUR CLOCK (Set Hour) before attempting to set
timer functions.
You can set the Start Time and Stop Time a minimum of one hour
apart, and a maximum of 23 hours apart.
After setting the time, press the Set Hour button once (Start
light on). Use the buttons to select the time that the
and
unit will START.
After selecting the Start Time, press the Set Hour button once.
(Stop Light on). Use the
and
buttons to select the time
that the unit will STOP. After selecting the stopping time, press
the Set Hour button once.
10
Press the Timer On/Off button (light turns on) to activate the
timer function. To deactivate this function, press the Timer On/
Off button once again (light turns off). Once the on and off times
have been selected, they will remain in memory and cycle daily
until changed.
NOTE: If the unit is unplugged or the power is interrupted, the HOUR
must be reset or the Timer On/Off will not function when desired.
To Re-Activate Money Saver
Press the Check Filter button to reset the timer.
noit id noc ria moor hcirdeirF ruoy etarepo ot woH er
Inspect product prior to installation.
If your air conditioner is installed and plugged into a proper
receptacle, it is ready to go. The first time the unit is started,
the compressor will delay for three minutes. See Automatic
Component Protection on the following page (See Figures 1
& 2, page 5.
to activate the Fan Only feature.
2 Press the MoneySaver
®
button to activate the MoneySaver
®
feature. The light will indicate MoneySaver
®
is in use.
11 The Check Filter light comes on when the filter needs cleaning.
Check Filter Light
2
5
On WY/WE heat-cool
models, continuing from Fan Only
mode, press the System button once to activate heat mode.
MoneySaver® is a feature that cycles the fan with the
compressor so that the fan does not run all the time.
This saves energy and improves dehumidification.
MoneySaver® will also run to test the temperature
when the off cycle is too long. Or you may prefer
constant fan for more air movement. To deactivate
MoneySaver® and go to Constant Fan, press the
MoneySaver® button.
Press both the and buttons at the same time to switch
the temperature from Fahrenheit (°F) to Celsius (°C).
Repeat these steps to switch from °C back to °F.
Loading ...
Loading ...
Loading ...