Frigidaire FWFB9200ES0 washer

User Manual - Page 12

For FWFB9200ES0.

PDF File Manual, 12 pages, Download pdf file

Loading ...
Loading ...
Loading ...
OCCURRENCE
OPERA TING
Washer does not start.
POSSIBLE CAUSE / SOLUTION
Electrical power cord may not be plugged in or connection may be loose. Make
sure plug fits tightly in wall outlet.
House fuse blown, circuit breaker tripped, or a power outage hasoccurred.
Resetcircuit breaker or replace fuse. Do not increase fuse capacity. If problem is
a circuit overload, have it corrected by a qualified electrician. If problem is a
power outage, call local electric company.
Water supply faucets are not turned on. Turn on water supply faucets.
Motor isoverheated. Washer motor will stop if it becomes overheated. It will
automatically restart after a cool down period of up to 30 minutes (if washer has
not been manually turned off).
Dispenser drawer isnot completely closed. Close dispenser drawer.
Washer won't spin.
Washer door isnot completely closed. Close door completely.
Dispenser drawer isnot completely closed. Close dispenser drawer.
Load istoo small. Add 1 or 2 similar items to help balance the load.
Residue left in drum. Heavily soiled items. Wipe drum with a nonabrasive household cleanser, then
rinse. Shake or brush excess dirt and sand from items before washing.
WATER
Water collects in folds of the This is a result of the washing action and ispart of the normal operation of the
bellows at the end of the cycle, washer.
Water collects in bleach and fabric This isa result of the siphoning action and is part of the normal operation of the
softener compartments, washer. Water may be removed by removing the dispenser drawer (see Page
10, Figures 1 and 2) and draining water into the empty drum or sink.
Wash load too wet after spin. Washer isoverloaded. Do not overload washer. See Washing Procedures.
Load istoo small. Add 1 or 2 similar items to help balance the load.
Load isout of balance. Rearrange load to allow proper spinning.
Drain hose iskinked. Straighten drain hose.
Water does not enter washer or it
enters slowly.
Water supply is not adequate in area. Check another faucet in the house. Wait
until water supply and pressure increase.
Water supply faucets are not completely open. Fully open hot and cold faucets.
Water is being used elsewhere in the house. Water pressure must be at least 30
psi (260 kPa). Avoid running water elsewhere while washer isfilling.
Water inlet hosesare kinked. Straighten hoses.
Warm or hot water is not hot
enough.
Hot water heater isset too low or isa distance from washer. Measure hot water
temperature at nearby faucet with candy or meat thermometer. Water
temperature should be at least !20% (49°C). Adjust water heater asnecessary.
Hot water isbeing used elsewhere in the house. Avoid using hot water
elsewhere before or during washer use. There may not be enough hot water
available for proper (:leaning. If problem persists, your hot water system may be
unable to support more than 1 useat a time.
Water in washer does not drain or
drains slowly. Drain hose iskinked or clogged. Clean and straighten the drain hose.
Maximum standpipe height is 8' (2.4 m).
Waterleaks. Fillhose connection isloose at faucet or washer. Check and tighten hose
connections. Install rubber sealing washers provided.
House drain pipes are clogged. Unclog drain pipes. Contact plumber if
necessary.
Oversudsing. Wrong detergent. Run rinse cycle. Use a low-sudsing, high efficiency detergent.
Too much detergent. Run rinse cycle. Use lessdetergent in future loads
Incorrect wash andrinse Hot and cold water hoses are connected to wrong supply faucets. Connect hot
temperatures, water hoseto hot water faucet and cold water hose to (:old water faucet.
Wateris entering washerbut tub Drain hose standpipe is incorrect height. Standpipe must be aminimum of 23.6"
does not fill. (60 cm) high to prevent siphoning. See INSTALLATIONINSTRUCTIONS.
12