Loading ...
Loading ...
Loading ...
Tools needed for installation:
• Adjustable or open end • Ruler or measuring tape
wrench %6" (14 mm)
• Pliers that open to 1%6"
• Level (3.95 cm)
• Wood block • Flashlight (optional)
Alternate Parts
Your installation may require additional parts. For information on ordering, please refer to the
toll-free phone numbers on the front page of the Use and Care Guide.
If You Have: You Will Need to Buy:
[aundry tub or standpipe Sump pump system (if not already available)
taller than 96" (2.4 m)
1" (2.5 cm) diameter 1%" (3.2 cm) diameter to 1" (2.5 cm) diameter standpipe
standpipe adapter, Part Number 280130
Overhead sewer Standard 20 gal. (76 [.) 39" (99 cm) tall drain tub or utility
sink, sump pump and connectors (available from local
plumbing suppliers)
Floor drain Siphon break kit, Part Number 280129; additional drain hose,
Part Number 3357090
Water faucets beyond 2 longer water fill hoses:
reach of fill hoses 6 ft (1.8 m) Part Number 76314,
10 ft (3.0 m) Part Number 350008
Drain hose too short Kit Part Number 2801 31
lint clogged drain [)rain protector, Part Number 367031
LOCATION REQU I REMENTS
Selecting the proper location for your washer improves performance and minimizes noise and
possible washer "walk."
Your washer can be installed in a basement, laundry room, closet, or recessed area. See
"Drain System."
IMPORTANT: Do not install or store the washer where it will be exposed to the weather.
Proper installation is your responsibility.
You will need:
• A water heater set to deliver 120°F 149°C) water to the washer.
• A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is
attached to the back of the washer. See "Electrical Requirements."
• Hot and cold water faucets located within 3 ft (90 cm) of the hot and cold water fill
valves, and water pressure of 5-100 psi/34.5-690 kPa). Washers with triple dispensers
require 20-100 psi (138-690 kPa) for best performance.
• A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the
washer on carpeting is not recommended.
• A sturdy floor to support the washer weight (washer, water and load) of 315 Ibs (143 kgs).
Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can
remain in the washer and can cause damage in low temperatures. See "Washer Care."
Recessed area or closet installation
The dimensions shown are for the recommended spacing allowed (A and B), except the closet
door ventilation openings. [he dimensions shown for the closet door ventilation openings (C)
are the minimum required.
m
n
olo
16,,5[-
(46.3cm)
,2
[_ 24n -
(1__m_)
O"T_-_-- 27"_6" -_-11"1_-25_/_"_1 1<-4"
(Ocm) (68.6crn) (0¢rn) (2.Scrn) (64,80rn) (1O.2¢rn)
A B
__ _ 3"
(7,6crn)
NNN-
__ _ 3"
(7.6cm)
C
A. Frollt vi(!w
8. Side view
(7. Closet door with vents
• Additional spacing should be considered for ease of installation and servicing.
• Additional clearances may be required for wall, door and floor moldings.
• Additional spacing of 1" (2.5 cm) on all sides of the washer is recommended to reduce
noise transfer.
• If a closet door is installed, the minimum air openings in the top and bottom of the door
are required (C). [ ouvered doors with air openings in the top and bottom are acceptable.
• Companion appliance spacing should also be considered.
DRAIN SYSTEM
The washer can be installed using the standpipe drain system (floor or wall), the laundry tub
drain system, or the floor drain system. Select the drain hose installation method you need.
See '"ibols and Parts."
Standpipe drain system--wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum
carry-away capacity can be no less than 17 gal. (64 L) per minute. A 1V,¢ (3.2 cm) diameter to
1" (2.5 cm) diameter standpipe adapter kit is available. See "]bols and Parts."
The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (244 cm/
from the bottom of the washer.
I
Loading ...
Loading ...
Loading ...