Loading ...
Loading ...
Loading ...
MAINTENANCE
-Cleaning
Before any type of operation, always make sure that the electrical cord is disconnected and the switch is in the off position.
Clean the external part with a mild, liquid detergent and avoid the use of abrasive cleaning products.
-Changing the light
Before changing the light make sure that the hood is not connected.
Remove the grease filter and replace the light with a light bulb no more powerful than that specified in the Technical
Characteristics. Place the filter in position.
-Cleaning the grease filter.
Depending on use, and at least once a month the grease filters should be disassembled and cleaned in a dishwasher or with
hot soapy water.
If washed in a dishwasher, the filters should be placed in an upright position to prevent food remains from falling on them.
After rinsing and drying, replace the filters by following the steps for disassembly in reverse order.
The active carbon filters must be replaced periodically to work properly, at least once every three months (depending on the
frequency with which the hood is used).
IMPORTANT WARNING FOR EXTRACTOR HOODS WITH HALOGEN LAMPS
If the halogen lamps need replacing, they must be replaced by lamps with an aluminium reflector, never dichroic lamps, to
avoid unnecessary overheating in the lamp holders.
THE MANUFACTURER WAIVES ALL LIABILITY FOR FAILURE TO OBSERVE THE INSTRUCTIONS FOR THE
APPROPRIATE INSTALLATION, MAINTENANCE AND USE OF THE EXTRACTOR HOOD.
The manufacturer declares that this product meets all the essential requirements for low voltage electrical material set out in
European directive 2006/95/EEC of 12 December 2006 and for electromagnetic compatibility as required by European
directive 2004/108/EEC of 15 December 2004.
If you need any technical help or would like more information about our products, please do not hesitate to contact our official
distributor.
THE MANUFACTURER reserves the right to effect any technological improvement or modification without prior
notice.
IMPORTANT:
•
Do not connect the hood to chimneys, ventilation pipes or hot air pipes. Before connecting any pipes, consult municipal ordinances on exhaust air and
request permission from the person in charge of the building. Be sure there is adequate ventilation, even in cases where the hood is to be used
simultaneously with another product.
•
Never leave frying food unattended since grease can overheat and catch fire. The risk of fire is even greater in the case of used oil.
•
Never use the hood in areas where devices with exhaust pipes connected to the outside are already operating unless perfect ventilation can be
guaranteed.
•
To avoid the possibility of fire, adhere strictly to all of the recommendations included here and to the periodic cleaning of the grease filters.
•
During an electrostatic discharge (ESD) it is possible that the device will stop working. By switching the device OFF an ON the device will again work
as intended. There is no risk and no risk will appear.
•
If the supply cord of this equipment is damaged, it must only be replaced by manufacturer or it’s service agent or similarly qualified person in order to
avoid a hazard.
•
Never have a lighted flame under the extractor hood.
•
The appliance must be placed in such a way, that the supply plug is accessible.
•
The hood must be installed at a minimum distance of 65cm from the stovetop.
•
During climatic conditions causing electrical interference, it is possible that the device may stop working. By switching the device OFF and ON the
device will resume normal operation safety.
•
This hood is not designed to be used by people (including children) with reduced physical, sensorial or mental capacity, or who lack experience or
knowledge about it, unless they have had supervision or instructions on how to use the hood by someone who is responsible for their safety.
•
Children must be supervised to ensure that they do not play with the hood.
•
The evacuated air must not be sent along conduits that are used to evacuate smoke from devices powered by gas or other fuels (this does not apply to
devices used exclusively to discharge air inside the room).
•
When the extractor hood is turned on at the same time as other appliances powered by energy other than electricity, the air outlet must not be greater
than 4 Pa (4x10-5 bar).
•
Never use the hood in places where appliances are already operating with outputs connected to the exterior unless perfect ventilation of the place can
be ensured.
•
This hood can only be installed over electric or gas hobs with a maximum of 6 cooking points.
•
If the extractor hood is installed over a gas cooking appliance, the minimum distance between the surface supporting the cooking elements and the
lower part of the hood must be at least 65 cm. If the installation instructions for the gas cooker indicate a greater distance, this should be observed.
•
If the extractor hood is installed over an electric cooking appliance, the minimum distance to be left between the surface supporting the cooking
elements and the lower part of the hood is described in the assembly plan.
•
The regulations with respect to air evacuation must be respected.
Loading ...
Loading ...
Loading ...