Loading ...
Loading ...
Loading ...
P.09
P.10
Installation Requirements
Installation Requirements
1.A120v.60Hz,AConly,15-or 20amp,fused electrical supply is required. A time-delay fuse or
circuit serving only this appliance be provided .
2.This washer is equipped with a power supply cord having a 3 prong grounding plug.
3.To minimize possible shock hazard ,the cord must be plugged into a mating,3 prong,
grounding type outlet ,grounded in accordance with accordance with local codes and
ordinances. If a mating outlet is not available ,it is the personal responsibility and obligation
of the customerto have the properly grounded outlet installed by a qualified electrician.
4.If codes permit and a separate ground wire is used ,it is recommended that a qualified
electrician determine that the ground path is adequate.
5.Do not ground to a gas pipe .
6.Check with a qualified electrician if you are not sure the washer is properly grounded.
7.Do not have a fuse in the neutral or ground circuit.
Location requirements
Selecting the proper location for your washer improves performance and minimizes noise
and possible washer “walk.”Your washer can be installed under a custom counter,or in a
basement, laundry room, closet, or recessed area. See “Drain System.”Companion
appliance location requirements should also be considered. Proper installation is your
responsibility.
You will need
1. A water heater set to deliver 1 20°F (49°C) water to the washer.
2. A grounded electrical outlet located within 6 ft.( 1.8 m) of where the power cord is
attached to the back of the washer.See “Electrical Requirements.”
3. Hot and cold water faucets located within 4 ft.(1.2 m)of the hot and cold water fill
valves,and water pressure of 2 0- 100 psi ( 13 7.9-6 89 .6 kPa).
4. A level floor with a maximum slope of 1" (25 mm)under entire washer.Installing the washer
on soft floor surfaces,such as carpets or surfaces with foam backing.is not recommended.
5. A sturdy and solid floor to support the washer with a total weight (water and load) of 200lbs.
6. Do not operate your washer in temperatures below 32°F (0°C).Some water can
remain in the washer and can cause damage in low temperatures.
Installation clearances
1.The location must be large enough to allow the washer door to be fully opened.
°
2. Additional spacing should be considered for ease of installation and servicing. The door
opens more than 90 ,and it is nor reversible.
3. Additional clearances might be required for wall ,door , and floor moldings.
4. Additional spacing of 25mm on all sides of the washer is recommended to reduce noise
transfer.
5. Companion appliance spacing should also be considered.
Electrical requirements
WARNING
Electrical Shock Harzard
Connect to grounded 3 prong outlet with an individual 12 amp
branch circuit protected by a 12 amp circuit breaker.
Connect to individual branch circuit.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in electrical
shock, fire, or death.
Electrical requirements
Washer dimensions
The dimensions shown are for the recommended spacing. Custom dercounter installation
23
"
( 595 mm)
1
"
(25 mm)
1
"
(25 mm)
2
" (50 mm)
" min.
(850 mm)
1
/2
1
/2
1
/2
4
2
"
(1080 mm)
1
/2
23
"
(595 mm)
33
33
"
(850mm)
Unpacking the washing machine
Unpack your washing machine and check if there is any damage during the transportation.
Also make sure that all the items (as shown in Page 5) in the attached bag arereceived.
If there is any damage to the washing machine during the transportation, or anyitem is
missing, please contact the local dealer immediately.
1
/2
1
/2
23
"
(595 mm)
Loading ...
Loading ...
Loading ...