continued >
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model
and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
1
Check that the internal cabinetry dimensions are correct (see Diagram 1a/b).
2
Unpack the refrigerator as per instructions on carton.
IMPORTANT!
●
Due to the size of the refrigerator(s), it is essential that assembly of the surround kit be undertaken with a minimum of two able-
bodied persons.
●
It is important to include adequate venting to the top of the refrigerator, to ensure efficient operation.
●
The installation of the refrigerator(s) can be at floor level as shown in Diagram 1a or installed above the toe kick board as in
Diagram1b.
●
Rollers and feet must be fitted.
●
Refrigerators installed above the toe kit should have a floor base constructed to support the total weight of the loaded
refrigerator(s) placed on it.
The placement of the 5/8” (16mm) MDF or plywood under the refrigerator(s) on either installation type is to allow the fitment of the
bottom trim that covers it. It is optional.
4
GETTING STARTED
This kit is designed to be used with models with a refrigerator height of between: 663/4– 711/8” (1695 – 1806mm) with curved or
flat door styling. You can find the part number for each installation in Section 2.
To give the most integrated look, the kitchen cabinetry should be flush with the front of the refrigerator door.
Tools required (not included)
●
No. 2 drill bit – long.
●
Electric drill.
●
Phillips screwdriver.
●
1 x 5/8” (16mm) piece of MDF the same size as the base of the cavity (optional). Not needed if refrigerator is
sitting directly on the floor and not on raised toe kickarea.
●
Joiner kit (part number 819264) required if joining two refrigerators side by side.
1
REFRIGERATOR SURROUND KIT
RF135B RF135B RF135B
RF170W
RF170B
RF170W
RF170B
RF170W
RF170B
RF170A
RF201A
REFRIGERATOR MODEL 1 X RF135B 2 X RF135B
1 X RF170W
1 X RF170B
2 X RF170W
2 X RF170B
1 X RF170A
(French door model)
1 X RF201A
(French door model)
CAVITY DIMENSIONS (Flush to edge of door) inches (mm) inches (mm) inches (mm) inches (mm) inches (mm) inches (mm)
A
Width
3113/16” (807) 573/4” (1467) 377/8” (962) 70” (1777) 377/8” (962) 421/4” (1072)
B
Depth*
279/16” (700) 279/16” (700) 279/16” (700) 279/16” (700) 279/16” (700) 279/16” (700)
C
1 Height**
701/2” (1790) 701/2” (1790) 701/2” (1790) 701/2” (1790) 701/2” (1790) 7313/16” (1875)
C
2 Height***
711/8” (1806) 711/8” (1806) 711/8” (1806) 711/8” (1806) 711/8” (1806) 741/2” (1891)
D
Air vent depth
8” (200) 8” (200) 8” (200) 8” (200) 8” (200) 8” (200)
E
Air vent width
1913/16” (502) 453/4” (1162) 257/8” (657) 58” (1472) 257/8” (657) 301/4” (767)
KIT PART NUMBERS LH RH LH RH
Brushed Stainless 24468 24469 24470 24474 24475 24476 24478 24477
Plus Joiner Kit 819264 819264
* Depth is a minimum requirement.
** Height is without 5/8” (16mm) MDF packer.
*** Height is with 5/8” (16mm) MDF packer.
Cavity dimensions above are to be used as minimum dimensions.
A
B
D
E
C
1
Diagram 1a
Refrigerator at floorlevel
B
E
D
A
C
2
Diagram 1b
Refrigerator above toekick
Diagram 1
2
KIT PART NUMBERS AND CAVITY DIMENSIONS TABLE
All dimensions are internal or cavity dimensions.
The refrigerator can be installed:
1
In a cavity with 5/8” (16mm) panel (bottom trim attached), or in a cavity where the
product is at floor level (no bottom trim). (Diagram 1a).
2
In a cavity with a toe kick under the product with the bottom trim fitted to the base
(Diagram 1b).
3
Check whether your fridge has hinges concealed by the front of the fridge door.
For refrigerators/freezers where the hinge is not concealed by the door refer to
spare parts for the correct kit number. 820413 D should list non concealed number kit.
3
BEFORE INSTALLATION
Concealed hinge Non concealed hinge
US CA
REFRIGERATOR SURROUND KIT
IN STALLATI ON GUIDE
RF135B, RF170B, RF170W, RF170A & RF201A models
continued >
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model
and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
1
Check that the internal cabinetry dimensions are correct (see Diagram 1a/b).
2
Unpack the refrigerator as per instructions on carton.
IMPORTANT!
●
Due to the size of the refrigerator(s), it is essential that assembly of the surround kit be undertaken with a minimum of two able-
bodied persons.
●
It is important to include adequate venting to the top of the refrigerator, to ensure efficient operation.
●
The installation of the refrigerator(s) can be at floor level as shown in Diagram 1a or installed above the toe kick board as in
Diagram1b.
●
Rollers and feet must be fitted.
●
Refrigerators installed above the toe kit should have a floor base constructed to support the total weight of the loaded
refrigerator(s) placed on it.
The placement of the 5/8” (16mm) MDF or plywood under the refrigerator(s) on either installation type is to allow the fitment of the
bottom trim that covers it. It is optional.
4
GETTING STARTED
This kit is designed to be used with models with a refrigerator height of between: 663/4– 711/8” (1695 – 1806mm) with curved or
flat door styling. You can find the part number for each installation in Section 2.
To give the most integrated look, the kitchen cabinetry should be flush with the front of the refrigerator door.
Tools required (not included)
●
No. 2 drill bit – long.
●
Electric drill.
●
Phillips screwdriver.
●
1 x 5/8” (16mm) piece of MDF the same size as the base of the cavity (optional). Not needed if refrigerator is
sitting directly on the floor and not on raised toe kickarea.
●
Joiner kit (part number 819264) required if joining two refrigerators side by side.
1
REFRIGERATOR SURROUND KIT
RF135B RF135B RF135B
RF170W
RF170B
RF170W
RF170B
RF170W
RF170B
RF170A
RF201A
REFRIGERATOR MODEL 1 X RF135B 2 X RF135B
1 X RF170W
1 X RF170B
2 X RF170W
2 X RF170B
1 X RF170A
(French door model)
1 X RF201A
(French door model)
CAVITY DIMENSIONS (Flush to edge of door) inches (mm) inches (mm) inches (mm) inches (mm) inches (mm) inches (mm)
A
Width
3113/16” (807) 573/4” (1467) 377/8” (962) 70” (1777) 377/8” (962) 421/4” (1072)
B
Depth*
279/16” (700) 279/16” (700) 279/16” (700) 279/16” (700) 279/16” (700) 279/16” (700)
C
1 Height**
701/2” (1790) 701/2” (1790) 701/2” (1790) 701/2” (1790) 701/2” (1790) 7313/16” (1875)
C
2 Height***
711/8” (1806) 711/8” (1806) 711/8” (1806) 711/8” (1806) 711/8” (1806) 741/2” (1891)
D
Air vent depth
8” (200) 8” (200) 8” (200) 8” (200) 8” (200) 8” (200)
E
Air vent width
1913/16” (502) 453/4” (1162) 257/8” (657) 58” (1472) 257/8” (657) 301/4” (767)
KIT PART NUMBERS LH RH LH RH
Brushed Stainless 24468 24469 24470 24474 24475 24476 24478 24477
Plus Joiner Kit 819264 819264
* Depth is a minimum requirement.
** Height is without 5/8” (16mm) MDF packer.
*** Height is with 5/8” (16mm) MDF packer.
Cavity dimensions above are to be used as minimum dimensions.
A
B
D
E
C
1
Diagram 1a
Refrigerator at floorlevel
B
E
D
A
C
2
Diagram 1b
Refrigerator above toekick
Diagram 1
2
KIT PART NUMBERS AND CAVITY DIMENSIONS TABLE
All dimensions are internal or cavity dimensions.
The refrigerator can be installed:
1
In a cavity with 5/8” (16mm) panel (bottom trim attached), or in a cavity where the
product is at floor level (no bottom trim). (Diagram 1a).
2
In a cavity with a toe kick under the product with the bottom trim fitted to the base
(Diagram 1b).
3
Check whether your fridge has hinges concealed by the front of the fridge door.
For refrigerators/freezers where the hinge is not concealed by the door refer to
spare parts for the correct kit number. 820413 D should list non concealed number kit.
3
BEFORE INSTALLATION
Concealed hinge Non concealed hinge
US CA
REFRIGERATOR SURROUND KIT
IN STALLATI ON GUIDE
RF135B, RF170B, RF170W, RF170A & RF201A models
continued >
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model
and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
1
Check that the internal cabinetry dimensions are correct (see Diagram 1a/b).
2
Unpack the refrigerator as per instructions on carton.
IMPORTANT!
●
Due to the size of the refrigerator(s), it is essential that assembly of the surround kit be undertaken with a minimum of two able-
bodied persons.
●
It is important to include adequate venting to the top of the refrigerator, to ensure efficient operation.
●
The installation of the refrigerator(s) can be at floor level as shown in Diagram 1a or installed above the toe kick board as in
Diagram1b.
●
Rollers and feet must be fitted.
●
Refrigerators installed above the toe kit should have a floor base constructed to support the total weight of the loaded
refrigerator(s) placed on it.
The placement of the 5/8” (16mm) MDF or plywood under the refrigerator(s) on either installation type is to allow the fitment of the
bottom trim that covers it. It is optional.
4
GETTING STARTED
This kit is designed to be used with models with a refrigerator height of between: 663/4– 711/8” (1695 – 1806mm) with curved or
flat door styling. You can find the part number for each installation in Section 2.
To give the most integrated look, the kitchen cabinetry should be flush with the front of the refrigerator door.
Tools required (not included)
●
No. 2 drill bit – long.
●
Electric drill.
●
Phillips screwdriver.
●
1 x 5/8” (16mm) piece of MDF the same size as the base of the cavity (optional). Not needed if refrigerator is
sitting directly on the floor and not on raised toe kickarea.
●
Joiner kit (part number 819264) required if joining two refrigerators side by side.
1
REFRIGERATOR SURROUND KIT
RF135B RF135B RF135B
RF170W
RF170B
RF170W
RF170B
RF170W
RF170B
RF170A
RF201A
REFRIGERATOR MODEL 1 X RF135B 2 X RF135B
1 X RF170W
1 X RF170B
2 X RF170W
2 X RF170B
1 X RF170A
(French door model)
1 X RF201A
(French door model)
CAVITY DIMENSIONS (Flush to edge of door) inches (mm) inches (mm) inches (mm) inches (mm) inches (mm) inches (mm)
A
Width
3113/16” (807) 573/4” (1467) 377/8” (962) 70” (1777) 377/8” (962) 421/4” (1072)
B
Depth*
279/16” (700) 279/16” (700) 279/16” (700) 279/16” (700) 279/16” (700) 279/16” (700)
C
1 Height**
701/2” (1790) 701/2” (1790) 701/2” (1790) 701/2” (1790) 701/2” (1790) 7313/16” (1875)
C
2 Height***
711/8” (1806) 711/8” (1806) 711/8” (1806) 711/8” (1806) 711/8” (1806) 741/2” (1891)
D
Air vent depth
8” (200) 8” (200) 8” (200) 8” (200) 8” (200) 8” (200)
E
Air vent width
1913/16” (502) 453/4” (1162) 257/8” (657) 58” (1472) 257/8” (657) 301/4” (767)
KIT PART NUMBERS LH RH LH RH
Brushed Stainless 24468 24469 24470 24474 24475 24476 24478 24477
Plus Joiner Kit 819264 819264
* Depth is a minimum requirement.
** Height is without 5/8” (16mm) MDF packer.
*** Height is with 5/8” (16mm) MDF packer.
Cavity dimensions above are to be used as minimum dimensions.
A
B
D
E
C
1
Diagram 1a
Refrigerator at floorlevel
B
E
D
A
C
2
Diagram 1b
Refrigerator above toekick
Diagram 1
2
KIT PART NUMBERS AND CAVITY DIMENSIONS TABLE
All dimensions are internal or cavity dimensions.
The refrigerator can be installed:
1
In a cavity with 5/8” (16mm) panel (bottom trim attached), or in a cavity where the
product is at floor level (no bottom trim). (Diagram 1a).
2
In a cavity with a toe kick under the product with the bottom trim fitted to the base
(Diagram 1b).
3
Check whether your fridge has hinges concealed by the front of the fridge door.
For refrigerators/freezers where the hinge is not concealed by the door refer to
spare parts for the correct kit number. 820413 D should list non concealed number kit.
3
BEFORE INSTALLATION
Concealed hinge Non concealed hinge
US CA
REFRIGERATOR SURROUND KIT
IN STALLATI ON GUIDE
RF135B, RF170B, RF170W, RF170A & RF201A models
continued >
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model
and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
1
Check that the internal cabinetry dimensions are correct (see Diagram 1a/b).
2
Unpack the refrigerator as per instructions on carton.
IMPORTANT!
●
Due to the size of the refrigerator(s), it is essential that assembly of the surround kit be undertaken with a minimum of two able-
bodied persons.
●
It is important to include adequate venting to the top of the refrigerator, to ensure efficient operation.
●
The installation of the refrigerator(s) can be at floor level as shown in Diagram 1a or installed above the toe kick board as in
Diagram1b.
●
Rollers and feet must be fitted.
●
Refrigerators installed above the toe kit should have a floor base constructed to support the total weight of the loaded
refrigerator(s) placed on it.
The placement of the 5/8” (16mm) MDF or plywood under the refrigerator(s) on either installation type is to allow the fitment of the
bottom trim that covers it. It is optional.
4
GETTING STARTED
This kit is designed to be used with models with a refrigerator height of between: 663/4– 711/8” (1695 – 1806mm) with curved or
flat door styling. You can find the part number for each installation in Section 2.
To give the most integrated look, the kitchen cabinetry should be flush with the front of the refrigerator door.
Tools required (not included)
●
No. 2 drill bit – long.
●
Electric drill.
●
Phillips screwdriver.
●
1 x 5/8” (16mm) piece of MDF the same size as the base of the cavity (optional). Not needed if refrigerator is
sitting directly on the floor and not on raised toe kickarea.
●
Joiner kit (part number 819264) required if joining two refrigerators side by side.
1
REFRIGERATOR SURROUND KIT
RF135B RF135B RF135B
RF170W
RF170B
RF170W
RF170B
RF170W
RF170B
RF170A
RF201A
REFRIGERATOR MODEL 1 X RF135B 2 X RF135B
1 X RF170W
1 X RF170B
2 X RF170W
2 X RF170B
1 X RF170A
(French door model)
1 X RF201A
(French door model)
CAVITY DIMENSIONS (Flush to edge of door) inches (mm) inches (mm) inches (mm) inches (mm) inches (mm) inches (mm)
A
Width
3113/16” (807) 573/4” (1467) 377/8” (962) 70” (1777) 377/8” (962) 421/4” (1072)
B
Depth*
279/16” (700) 279/16” (700) 279/16” (700) 279/16” (700) 279/16” (700) 279/16” (700)
C
1 Height**
701/2” (1790) 701/2” (1790) 701/2” (1790) 701/2” (1790) 701/2” (1790) 7313/16” (1875)
C
2 Height***
711/8” (1806) 711/8” (1806) 711/8” (1806) 711/8” (1806) 711/8” (1806) 741/2” (1891)
D
Air vent depth
8” (200) 8” (200) 8” (200) 8” (200) 8” (200) 8” (200)
E
Air vent width
1913/16” (502) 453/4” (1162) 257/8” (657) 58” (1472) 257/8” (657) 301/4” (767)
KIT PART NUMBERS LH RH LH RH
Brushed Stainless 24468 24469 24470 24474 24475 24476 24478 24477
Plus Joiner Kit 819264 819264
* Depth is a minimum requirement.
** Height is without 5/8” (16mm) MDF packer.
*** Height is with 5/8” (16mm) MDF packer.
Cavity dimensions above are to be used as minimum dimensions.
A
B
D
E
C
1
Diagram 1a
Refrigerator at floorlevel
B
E
D
A
C
2
Diagram 1b
Refrigerator above toekick
Diagram 1
2
KIT PART NUMBERS AND CAVITY DIMENSIONS TABLE
All dimensions are internal or cavity dimensions.
The refrigerator can be installed:
1
In a cavity with 5/8” (16mm) panel (bottom trim attached), or in a cavity where the
product is at floor level (no bottom trim). (Diagram 1a).
2
In a cavity with a toe kick under the product with the bottom trim fitted to the base
(Diagram 1b).
3
Check whether your fridge has hinges concealed by the front of the fridge door.
For refrigerators/freezers where the hinge is not concealed by the door refer to
spare parts for the correct kit number. 820413 D should list non concealed number kit.
3
BEFORE INSTALLATION
Concealed hinge Non concealed hinge
US CA
REFRIGERATOR SURROUND KIT
IN STALLATI ON GUIDE
RF135B, RF170B, RF170W, RF170A & RF201A models
Before you call for service or assistance ...
Check the things you can do yourself. Refer to the Installation Instructions and your User Guide. Checkthat:
1
Your product is correctly installed.
2
You are familiar with its normal operation.
3
You have read the ‘Troubleshooting’ section at the back of the User Guide.
If after checking these points you still need assistance or parts, please contact your Fisher & Paykel trained and supported service
technician, Customer Care Centre, or contact us through our website www.fisherpaykel.com
!1
FURTHER INFORMATION
9
TRIM INSTALLATION
The bottom trim is designed to cover the front edge of the floor base panel of the
refrigerator. This trim can be installed on a raised toe kick (Diagram 1a) or toe kick
below the refrigerator (Diagram 1b)
Remembering that if this trim is to be used with the refrigerator at floor level the
cavity dimensions will need to have 5/8” (16mm) added to its height to allow for the
bottom trim to be fitted. Note this trim is optional on this type ofinstallation. If used
with a raised toe kick the 5/8” (16mm) packer should be part of the base (Diagram5).
Therefore 5/8” (16mm) is not required to be added to the height dimension.
1
If used place the 5/8” (16mm) piece of plywood or with bottom trim fitted into
thecavity (Diagram 5 or 6). Note: the piece should be the same size as the base of
thecavity.
2
Remove protective coating film from surround trim.
3
To install the surrounds, first clip in the top surround. Ensure the locator strips at the
rear of the top brackets clip into the rear of the top trim.
4
Clip both side trims into place starting from the front refrigerator edge.
5/8” (16mm) plywood
or MDF board insert
Part of base
Diagram 5
8
SECURE FLOOR STOPS
Two floor stops are supplied to prevent the
refrigerator from being pushed too far back
into the cavity. These are mounted on the
base or floor at a distance of 27” (688mm)
from the face front edge of the trim kit.
!0
MOVE INTO CAVITY
If installing two refrigerators/freezers side by side a joiner kit
is required. Refer to these instructions and fit joiner kit before
pushing refrigerator into place, see Diagram 6.
1
Plug refrigerator into electrical socket, run water connection to
refrigerator if required (Ice & Water models only).
2
Gently install refrigerator into cabinetry making sure it is
centered within the surround trim.
3
The front of the refrigerator door should be flush with the front
of the cabinetry to obtain anintegratedlook.
4
Ensure the front leveling feet are adjusted to take the load of
the fridge and keep it in place.
Optional
Diagram 6
5
PARTS SUPPLIED
Top trim (1)
Side trim (2)
Bottom trim (1)
Top trim brackets:
– Single refrigerator kits
(2 brackets)
– Side by Side kits
(3 brackets)
Side trim
center brackets
(6)
Screw type A:
#8 x 12 Pozi Drive CSK
(26)
Long screws
10 x 75 CSK PH
Part number: SP0207
(2)
Floor stops
Part number: 460912
(2)
Washer (3/16”)
(2)
Side trim brackets
(10)
Side trim brackets
(4)
7
SECURE SIDE TRIMBRACKETS
●
Locate the ten side trim brackets.
●
Position five brackets to the left hand side of the
cabinetry and the remaining five brackets to the right
hand side of the cabinetry.
●
Brackets should be evenly spaced down each side
(see Diagram 3a/b). Secure each of these brackets
with the two screws provided.
●
Care must be taken to line up the front edge of the
brackets with the leading edges of thecabinetry.
OR
6
SECURE TOP TRIMBRACKETS
●
Locate the two/three top trimbrackets.
●
For the side by side refrigerator kits, one bracket is to be
screwed in the top center of the cabinetry, secure the top
bracket with two of the screws (Type A, #8 x 12 PoziDrive
CSK) (see Diagram 2a).
●
For all other kits, the two brackets are to be secured on
either side, by two screws which are mounted from the side
(seeDiagram 2b).
●
Looking at the front of the refrigerator, place the top brackets
on top of the woodencabinetry.
●
Care must be taken to line up the top front edge of the
brackets with the leading edge of the cabinetry.
Hint: holes should be drilled in the center of the slot in the
brackets to allow for adjustment.
Diagram 2
Diagram 2b
End bracket
Diagram 2a
Centre bracket
OR
Diagram 3bDiagram 3a
6” (150mm)
27” (688mm)
Diagram 4
844987B 10.17
Before you call for service or assistance ...
Check the things you can do yourself. Refer to the Installation Instructions and your User Guide. Checkthat:
1
Your product is correctly installed.
2
You are familiar with its normal operation.
3
You have read the ‘Troubleshooting’ section at the back of the User Guide.
If after checking these points you still need assistance or parts, please contact your Fisher & Paykel trained and supported service
technician, Customer Care Centre, or contact us through our website www.fisherpaykel.com
!1
FURTHER INFORMATION
9
TRIM INSTALLATION
The bottom trim is designed to cover the front edge of the floor base panel of the
refrigerator. This trim can be installed on a raised toe kick (Diagram 1a) or toe kick
below the refrigerator (Diagram 1b)
Remembering that if this trim is to be used with the refrigerator at floor level the
cavity dimensions will need to have 5/8” (16mm) added to its height to allow for the
bottom trim to be fitted. Note this trim is optional on this type ofinstallation. If used
with a raised toe kick the 5/8” (16mm) packer should be part of the base (Diagram5).
Therefore 5/8” (16mm) is not required to be added to the height dimension.
1
If used place the 5/8” (16mm) piece of plywood or with bottom trim fitted into
thecavity (Diagram 5 or 6). Note: the piece should be the same size as the base of
thecavity.
2
Remove protective coating film from surround trim.
3
To install the surrounds, first clip in the top surround. Ensure the locator strips at the
rear of the top brackets clip into the rear of the top trim.
4
Clip both side trims into place starting from the front refrigerator edge.
5/8” (16mm) plywood
or MDF board insert
Part of base
Diagram 5
8
SECURE FLOOR STOPS
Two floor stops are supplied to prevent the
refrigerator from being pushed too far back
into the cavity. These are mounted on the
base or floor at a distance of 27” (688mm)
from the face front edge of the trim kit.
!0
MOVE INTO CAVITY
If installing two refrigerators/freezers side by side a joiner kit
is required. Refer to these instructions and fit joiner kit before
pushing refrigerator into place, see Diagram 6.
1
Plug refrigerator into electrical socket, run water connection to
refrigerator if required (Ice & Water models only).
2
Gently install refrigerator into cabinetry making sure it is
centered within the surround trim.
3
The front of the refrigerator door should be flush with the front
of the cabinetry to obtain anintegratedlook.
4
Ensure the front leveling feet are adjusted to take the load of
the fridge and keep it in place.
Optional
Diagram 6
5
PARTS SUPPLIED
Top trim (1)
Side trim (2)
Bottom trim (1)
Top trim brackets:
– Single refrigerator kits
(2 brackets)
– Side by Side kits
(3 brackets)
Side trim
center brackets
(6)
Screw type A:
#8 x 12 Pozi Drive CSK
(26)
Long screws
10 x 75 CSK PH
Part number: SP0207
(2)
Floor stops
Part number: 460912
(2)
Washer (3/16”)
(2)
Side trim brackets
(10)
Side trim brackets
(4)
7
SECURE SIDE TRIMBRACKETS
●
Locate the ten side trim brackets.
●
Position five brackets to the left hand side of the
cabinetry and the remaining five brackets to the right
hand side of the cabinetry.
●
Brackets should be evenly spaced down each side
(see Diagram 3a/b). Secure each of these brackets
with the two screws provided.
●
Care must be taken to line up the front edge of the
brackets with the leading edges of thecabinetry.
OR
6
SECURE TOP TRIMBRACKETS
●
Locate the two/three top trimbrackets.
●
For the side by side refrigerator kits, one bracket is to be
screwed in the top center of the cabinetry, secure the top
bracket with two of the screws (Type A, #8 x 12 PoziDrive
CSK) (see Diagram 2a).
●
For all other kits, the two brackets are to be secured on
either side, by two screws which are mounted from the side
(seeDiagram 2b).
●
Looking at the front of the refrigerator, place the top brackets
on top of the woodencabinetry.
●
Care must be taken to line up the top front edge of the
brackets with the leading edge of the cabinetry.
Hint: holes should be drilled in the center of the slot in the
brackets to allow for adjustment.
Diagram 2
Diagram 2b
End bracket
Diagram 2a
Centre bracket
OR
Diagram 3bDiagram 3a
6” (150mm)
27” (688mm)
Diagram 4
844987B 10.17
