Loading ...
Loading ...
Loading ...
75
ENGLISH
Basic versionSimple version InformationAdvanced version
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting Return to previous menu
Audio/Video Adjust
Setting items Setting details
S.Back
(Continued)
• This can also be set by pressing STANDARD.
• If the source being played contains a surround
back signal, the decoder type is automatically
selected by the AFDM function. Set “AFDM” to
“OFF” to switch to your preferred decoder.
NOTE
If the setting in “Speaker Config.” – “S.Back”
(vpage80) is “None”, “S.Back” is not displayed.
Speaker
Make settings for the
speakers outputting sound
when playing back in
DENON original surround
mode.
S.Back : Sound is output from the surround back speakers.
F.Wide : Sound is output from the front wide speakers.
F.Height : Sound is output from the front height speakers.
OFF : Sound is not output from the surround back speakers, front wide
speakers, and front height speakers.
NOTE
Only speakers that are set to something other than “None” in “Speaker
Config.” (vpage80) can be selected.
Subwoofer
Turn subwoofer output on
and off.
ON : The subwoofer is used.
OFF : The subwoofer is not used.
NOTE
This can be set when the surround mode is “DIRECT” (vpage 47),
“PURE DIRECT” (vpage47) and the “Subwoofer Mode” (vpage80) is
“LFE+Main”.
Default
The “Surround Parameter”
settings are returned to the
default settings.
Yes : Reset to the defaults.
No : Do not reset to the defaults.
n Tone
Adjust the tonal quality of the sound.
Setting items Setting details
Tone Control
Set the tone control function
to ON and OFF.
ON : Allow tone adjustment (bass, treble).
OFF : Playback without tone adjustment.
“Tone Control” can be set when “Dynamic EQ” (vpage76) is set to
“OFF”.
NOTE
• “Tone Control” settings are not reflected to ZONE2 and ZONE3.
• The tone cannot be adjusted in the direct mode.
Setting items Setting details
Bass
Adjust low frequency range
(bass).
–6dB – +6dB
“Bass” can be set when “Tone Control” is set to “ON”.
Treble
Adjust high frequency range
(treble).
–6dB – +6dB
“Treble” can be set when “Tone Control” is set to “ON”.
n Audyssey Settings
Default settings are underlined.
Set MultEQ
®
XT, Dynamic EQ
®
and Dynamic Volume™. These can be selected after Audyssey
®
Auto
Setup has been performed. For additional information on Audyssey technology, please see page 111.
NOTE
If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup,
you may not be able to select Dynamic EQ/Dynamic Volume, and “Run Audyssey” may be displayed.
In this case, either perform Audyssey Auto Setup over again or perform “Restore” (vpage10) to return to
the settings after Audyssey Auto Setup was run.
Setting items Setting details
MultEQ XT
Select one equalizer from
three modes. MultEQ XT
corrects both time and
frequency response
problems in the listening
area based on Audyssey
Auto Setup calibration. We
recommend “Audyssey”.
MultEQ XT is the
prerequisite function for
Dynamic EQ and Dynamic
Volume.
Audyssey : Optimize the frequency response of all speakers.
Audyssey Byp.L/R : Optimize frequency response of speakers except
front L and R speakers.
Audyssey Flat : Optimize frequency response of all speakers to flat
response.
Manual : Apply frequency response set with “Manual EQ” (vpage77).
OFF : Turn “MultEQ XT” equalizer off.
• “Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be
selected after Audyssey Auto Setup has been performed. “Audyssey”
is automatically selected after performing Audyssey Auto Setup. When
“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected,
illuminates.
• After running Audyssey Auto Setup, if the
Speaker Configuration, Distance, Channel
Level, and Crossover Frequency have changed
without increasing the number of speakers
measured, only
illuminates.
• Pressing MULTEQ makes this setting.
NOTE
• “MultEQ XT” and “Manual” cannot be selected when “EQ Customize”
is set to “Not Used” (vpage83).
• When using headphones, “MultEQ XT” is automatically set to “OFF”.
Loading ...
Loading ...
Loading ...