Loading ...
Loading ...
Loading ...
EN
33
:KHQWKH³VDIHW\VZLWFKRႇ´IXQFWLRQ
has been triggered, a 0 is displayed if
the glass surface temperature is not
dangerous for the user or an H if there
is a burn risk.
To reconnect the appliance, switch it
RႇE\SUHVVLQJWKHRQRႇNH\
(1) and
then switch it on again.
.HHSWKH FRQWURO SDQHO RI WKH
KHDWLQJDUHDVFOHDQDQGGU\DWDOOWLPHV
In case of operating problems
RULQFLGHQWVQRWPHQWLRQHGLQWKLV
PDQXDOGLVFRQQHFWWKHDSSOLDQFH
DQGFRQWDFWWKH60(*WHFKQLFDO
service.
5HFRPPHQGDWLRQIRUWKH
good use of vitroceramic
KREV
* Use pots or pans with thick,
FRPSOHWHO\ÀDWERWWRPV
* Pans with a smaller diameter than
the shown heating area are not
recommended.
* Do not slide pots and pans over the
glass as they may scratch it.
* Although the glass can withstand
knocks from large pots and pans
without sharp edges, try not to
knock it.
* To prevent damage to the ceramic
glass induction surface, try not
to slide the pots and pans over
the glass, and keep the bottoms
of the vessels clean and in good
condition.
Try not to spill sugar or
SURGXFWVFRQWDLQLQJVXJDURQ WKH
JODVVZKLOHWKHVXUIDFHLVKRWDV
WKHVHFRXOGGDPDJHLW
Cleaning and maintenance
To keep the appliance in good
condition, clean it using suitable
products and implements once it has
cooled down. This will make the job
easier and avoid the build-up of dirt
Never use harsh cleaning products or
tools that could scratch the surface, or
steam-operated equipment.
A pot or pan may become
VWXFNWRWKHJODVVGXHWRDSURGXFW
KDYLQJPHOWHGEHWZHHQWKHP'R
QRWWU\WROLIWWKHSRWZKLOHWKHKRW
SODWHLVFROG7KLVFRXOGFDXVHWKH
glass break.
'RQRW VWHS RQWKH JODVV RU
lean on it as it could break and
FDXVHLQMXU\'RQRWXVHWKHJODVV
DVDVXUIDFHIRUSXWWLQJREMHFWV
SMEG reserves the right to make
changes to its manuals that it deems
QHFHVVDU\RUXVHIXOZLWKRXWDႇHFWLQJ
the product’s essential features.
Environmental
considerations
7KHV\PERO RQWKHSURGXFW
RULWV SDFNDJLQJ PHDQV WKDW WKLV
product cannot be treated like
RUGLQDU\KRXVHKROGZDVWH7KLV
product must be taken to a recycling
collection point for electrical and
electronic appliances. By ensuring
WKDWWKLV SURGXFW LV GLVSRVHG RI
FRUUHFWO\ \RX ZLOO DYRLG KDUPLQJ
WKHHQYLURQPHQWDQGSXEOLFKHDOWK
ZKLFKFRXOGKDSSHQLIWKLVSURGXFW
LVQRWKDQGOHGSURSHUO\)RUPRUH
detailed information about recycling
WKLVSURGXFW SOHDVH FRQWDFW \RXU
ORFDODXWKRULW\KRXVHKROGZDVWH
VHUYLFHRU WKH VWRUH ZKHUH \RX
SXUFKDVHGWKHSURGXFW
7KHSDFNDJLQJPDWHULDOVXVHGDUH
environmentally-friendly and can
be recycled completely. Plastic
FRPSRQHQWVDUHPDUNHG!3(/'
!(36HWF'LVSRVHSDFNDJLQJ
PDWHULDOVOLNHKRXVHKROGZDVWHLQ
your local container.
,IVRPHWKLQJGRHVQRWZRUN
Before calling the technical service,
perform the verifications specified
below.
7KHDSSOLDQFHGRHVQRWZRUN
Ensure that the power cable is plugged
in.
7KHSRWVWLFNVWRWKHJODVV
If there is molten material between
the pot and the glass, set the hot
plate to maximum power and try to
separate them.
Single Sensor Error :
If any of the sensors is active more
than 10 seconds, this error situation
occurs and error code”F1” is showed.
7KLVHUURUFDQEHUHODWHGZLWKGLႇHUHQW
roots. One of them is that there may
be an object (fork, knife…) on the any
of the sensor.
Make sure that there is no any object
on the control unit, hob glass is wiped
with a dry cloth. If error situation
continue after this solution, please
WDNHRXWSOXJRUVZLWFKRႇIXVHVZLWFK
for 10 second.
Plural Sensor Error:
If more than 2 sensors are sensed at
same time, this error situation occurs
and error code”F2” is displayed.
3RWHQWLDO URRW UHDVRQV RI WKH
problem :
• There may be an object(pot…) or
ZDWHUDFFXPXODWLRQRYHUÀRZOLTXLG
from pot…) that cover more than 2
sensors
• Touch control location may
exposure more heat or steam
(from oven bottom of the hob…)
Please be sure that there is no any
REMHFWRQWKHVHQVRUVDQGVZLWFKHGRႇ
all steam and heat sources. Then,hob
glass is wiped with a dry cloth. If error
situation continue after this solution,
SOHDVHWDNHRXWSOXJRUVZLWFKRႇIXVH
switch for 10 second.
FC Error:
Fc message on the control and the
hot plates switch off: Overheating
in the electronics. Let thestove cool
for a while.