Loading ...
Loading ...
Loading ...
Review this chart to find do-it-yourself solutions for minor performance problems Any ser-
vice needed, other than those described in this owner's manual, should be performed by
an authorized service representative.
Disconnect electrical _ cleaning the unit.
Failure to do so could result in electrical shock or personal injury.
i,iii i ii ii i i ii iii1,11ql i[i,[i ii, i! I I
Unpluggedatwaltout,eL
Trippedcircuitbreakedblownfuse
at householdservicepanel
Loosehose electricalconnections
Trippedoverioadprotecior in
POWER.MATE_"
Cleaner won't start. 1.
2.
&
4o
Poor Job of dirt I.
pick-up. 2o
3,,
4_
5°
6.
7.
8.
9,
10.
Cleaner starts but 1,,
cuts off.
2.
POWER-MATE _ wilt not t.
run when attached°
2.
3,
4,
Performance indicator, 1,
some models, is red. 2,
3.
4o
Cleaner picks up moveable 1.
rugs -or- POWER-MATE _ 2,
Full or clogged dust bag
Clogged airflow passages
Dirty motor safety filter'
Wrong pl[e height setting
Open suction control
Hole in hose
Worn POWER-MATE _" brushes
Worn or broken belt
Dirty brush or brush supports
Canister hoed open
Hoseor hoodelectricalconnections
Trippedoverloadprotectorin
POWER-MATETM
3. Tripped overload protector
in canister
POWER-MATE _"connections
unplugged
Worn or broken belt
Dirty brush or brush supports
Tripped ovedoad protector in
POWER-MATE _'_
1_ Plug in firmly,pushONtOFF switchtoON
2. Resetcircuit breakeror replacefuse
3 Reconnect hose ends, (page 7)
4, Clean brush and brush supports,
then reset, (pages 14, t5)
1. Change bag, (page t2)
2. Clear airflow passages, (page I2)
3. Clean filter, (page 13).
4, Adjust setting, (page 9)
5, Adjust control, (page 11)
6. Replace hose
7. Change brushes, (page 16),
6 & 9, See BELT CHANGING AND BRUSH
CLEANING, (pages 14, I5)
10, Close and latch hood
1,
Check connections, reconnect hose
ends, (page 7).
2. Remove any items that may be caught
or jammed, then resel If cleaner starts
and stops again, clean brush and brush
supports, then reset, (pages 14, !5)
3, Change dust bag, clear airflow blockage,
(page 12) Wait 20 minutes for motor
to cool and automatically reset,
2&&
4.
Plugin firml_ (page 6),
See BELT CHANGING AND BRUSH
CLEANING, (pages 14, 15)
Check brush area for excessive lint
build-up or jammtng Clean brush and
brush supporls, then reset, (pages 14, 15)
Full or clogged dust bag t. Change bag, (page !2)
Dirty fitter 2 Change filter, (page 13)
Clogged airflow passage 3, Clear clog from airfiow passage, (page 12)
Certain attachment tools 4. This is normal Light should go off
when toolis removed.
Wrong pite height setting I, Adjust setting, (page 9)
Suction too strong 2. Open suction oonlro!, (page t t)
pushes too hard.
Light won't work_ 1. Burned out light bulb. 1. Change light bulb, (page 14)
Cord won't rewind, t, Dirty power cord, 1. Clean the power cord
2. Cord jammed. 2, Pui[ out cord and rewind,
Cleaner leaves marks 1. Wrong vacuuming pattern to See VACUUMING TIPS, (page 9)
on carpel
17
Loading ...
Loading ...
Loading ...