Loading ...
Loading ...
Starting the Refrigerator
Use of adapter plug
Because of potential safety hazards under certain
conditions, we strongly recommend against use of
an adapter plug_ However, if you still elect to use an
adapter, where local codes permit, a TEMPORARY
CONNECTION may be made to a properly grounded
two-prong walt outlet by use of a UL listed adapter
(Fig. 2) available at most local hardware stores.
The larger slot in the
adapter must be aligned
with the larger slot in the
wall outlet to provide
proper polarity in the
connection of the power
cord.
TEMPORARYMETHOD
IAOAPT_BFLUGSNOT
PeeMITTED_NCANADA) If -_'*_
Au_N_ARG_ [1tTf_I
I ] _'_'" INSUREPROPER
FIRMCONNECTION
Flg, 2 BEFOREUSE
CAUTION: Attaching an adapter ground terminal
to the wall outlet cover screw does not ground the
appliance unless the cover screw is metal, and not
insulated, and the wall outlet is grounded through
the house wiring° You should have circuit checked
by a qualified electrician to make sure the outlet
is properly grounded°
When disconnecting the power cord from the
adapter, always hold the adapter with one hand°
If this is not done, the adapter ground terminal is
very likely 1obreak with repeated use.
Should the adapter ground terminal break,
DO NOT USE the appliance until a proper
ground has again been established.
Use of Extension Cords
Because of potential safety hazards under certain
conditions, we strongly recommend against the use
of an extension cord_ However, if you still elect to use
an extension cord, it is absolutely necessary that it
be a UL listed 3-wire grounding type appliance
extension cord having a grounding type plug and
outlet and that the electrical rating of the cord be 15
amperes (minimum) and 120 "volts.
Electrical Requirements
The refrigerator should always be plugged into its
own individual electrical outletwll5 volt, 60 Hertz,
single phase AC. This is recommended for best
performance and to prevent overloading house
wiring circuits, which could cause a fire hazard
from overheating wires.
Location
a Install the refrigerator on a floor strong enough to
support it when it is fully loaded.
o Do not install it where the temperature will go
below 60°Fobecause it will not run often enough to
maintain proper temperatures.
q'Do not install it next to your range, a heating vent
or where the sun will shine directly on ira
Clearances
Allow the following clearances for ease of installation,
proper air circulation, and plumbing and electrical
connections:
Sides ...... 5/8" Top ....... 0" Back ...... 1"
(If built-in, allow 7/8" at top for hinge covers,)
Allow a 1Y2"door clearance at refrigerator side,
13/4" at freezer side.
Rollers
Adjustable rotters behind the base grille enable you to
move the refrigerator away from the wall for cleaning_
These rollers should be set so the refrigerator rests
firmly on the floor° Toassure that the doors will close
automatically from a halfway-open position, there is
a builtoin tilt from the front to the back of the cabinet.
Side-by-side refrigerators also have specially
designed door hinges that lift both doors slightly
when opened, allowing the force of gravity to help
close them securely.
To adjust the rollers:
• Remove the base grille_
Grasp it at the bottom
and pull it out.
o Turn the roller adjusting
screws clockwise to raise
the refrigerator, counter-
ciodcwise to lower it_Use
an adjustable wrench or
pliers on the 3/8" bolts,
Both doors should close
properly when bottom
front edge of refrigerator
cabinet is about 5/8"
from the floor.
- 1"oreplace the base
grille, line up the
prongs on the grille with
the clamps on the
refrigerator and push
forward until the grille
snaps into place.
I i
t i
Loading ...
Loading ...
Loading ...