Loading ...
2 B
CUTOUT FOR INSTALLATION OVER A
WARMING DRAWER
NOTE: Install the oven only with specific models listed on the label located on top of the oven.
NOTE: Additional clearances between cutouts may be required. Check to be sure the oven
supports above the Warming Drawer location do not obstruct the required interior depth and height.
When installing a Warming Drawer below a double oven, a separate 120V, 60 HZ, properly
grounded receptacle must be installed. Refer to installation instructions packed with the Warming
Drawer for specific installation requirements.
Anti-Tip Block Against
Rear Wall Per Warming
Drawer Requirement
2" (5.1 cm)
Min.
Per Warming
Drawer
Requirement
2 A
CUTOUT FOR DOUBLE OVENS (2 THERMAL
OVENS)
NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick,
shim both sides equally to establish the cutout width.
Dim. Description
30” Double Oven with
Pedestal
30” Double Oven without
Pedestal
A Cabinet width 30” (76.2 cm) 30” (76.2 cm)
B Cutout width 28
1
⁄2” (72.4 cm) min.
28
5
⁄8” (72.7 cm) max.
28
1
⁄2” (72.4 cm) min.
28
5
⁄8” (72.7 cm) max.
C Cutout height 51
13
⁄16” (131.6 cm) min.
51
15
⁄16” (131.9 cm) max.
50 ¼” (127.64cm)
D Clearance from cutout - side edges*
11
⁄16” (1.75 cm)
11
⁄16” (1.75 cm)
E Lower door clearance to adjacent corners,
drawers, walls, etc., When door is open
23” (53.3 cm) min. 23” (53.3 cm) min.
F Clearance from cutout - top* 1” (2.5 cm) min.(1
1
⁄4” (3.2 cm) 1” (2.5 cm) min.(1
1
⁄4” (3.2 cm)
G Clearance from cutout - bottom* 1
1
⁄4” (3.2 cm) 1
1
⁄4” (3.2 cm)
H Junction box location 9
1
⁄2” (24.1 cm) max.right side only 9
1
⁄2” (24.1 cm) max.right side only
K Recommended cutout location from floor 12” (30.5 cm) 12” (30.5 cm)
L French (upper) door swing depth - Allow additional
clearances for installation and oven usage
16
1
⁄4” (41.3 cm) min. 16
1
⁄4” (41.3 cm) min.
M Countertop or cabinet door protrusion
(measure if exist)
Measure “M” Measure “M”
N Gap between edge of countertop
or cabinet door to cabinet opening
If M = 0, N = 0, Otherwise
N = M + 1” (2.54 cm) min.
If M = 0, N = 0, Otherwise
N = M + 1” (2.54 cm) min.
P Junction Box location 5-1/4” (13.34 cm) max. 5-1/4” (13.34 cm) max.
R Junction Box location 2-1/2” (6.35 cm) max. 2-1/2” (6.35 cm) max.
S Door swing width - Allow additional clearances for
installation and oven usage
14” (35.6 cm) min. 14” (35.6 cm) min.
Continue to Section 3.
H
P
R
B
C
K
F
G
D
A
E
Junction Box
Location (junction
box may be
located in
adjacent cabinet)
Cutout Depth
23-1/2”
(59.7 cm) Min.
* Refers to minimum clearance required for wall oven installation and does not reflect actual product dimensions.
C
M
L L
N
S S
NOTE: Allow
1/4” (0.64 cm)
clearances from
side edges of
oven door.
Loading ...
Loading ...
Loading ...