Loading ...
4-Grill Setup
Parts Placement Checklist
Place the following items according to their position and orientation in
Fig. 4-1:
Flavor grids, cooking grids, backburner cover (if equipped), warming
rack, and meat probe.
Leave pre-installed E-burners in place to maintain proper alignment.
Backburner Cover (if equipped)
Hook the backburner cover over the top of the backburner to protect the
backburner from grease, dust and dirt when it is not in use.
Warming Rack
The warming rack comes pre-installed. Remove zip ties before use.
Consult the owner’s manual to remove or replace.
Shelf/Sideburner (if equipped)
Align the four (4) holes in the shelf with the four (4) holes in the side of
the cart while aligning and engaging the burner venturi with the orifi ce
(Fig. 4-2). Insert the four (4) screws (provided) into the holes and tighten.
Make the igniter wire connection as shown in Fig. 4-2. Open sideburner
lid, set cap on burner, and set grid into shelf.
Screws
Air shutter
Orifi ce
Igniter wire
Fig. 4-2
Venturi
Center main burner control knob
(A540s and larger only)
Fig. 5-2
Left
main burner
control knob
Right main burner
control knob
Backburner
control knob
(if equipped)
Digital
thermometer
(if equipped)
Meat probe
(if equipped)
Sideburner
control knob
(if equipped)
Drip tray
Fig. 4-1
Cooking grid
Flavor grid
(not with IR)
Backburner cover
(if equipped)
Warming
rack
Cotter
pin
Rotisserie
rod storage
ring
Sideburner
lid
Note: For infrared burner equipped
grills; see detailed instructions
included in your owner’s manual.
Meat probe
(if equipped)
Drip tray
liners
Drip tray (with
lighting instructions)
6-Propane Safety
Gas Cylinders
IMPORTANT: READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.
READ ALL SAFETY INSTRUCTIONS AND WARNINGS REGARDING THE USE OF PROPANE GAS FOUND IN
YOUR OWNER’S MANUAL.
5-Test
Light
switch
Light
switch
Grill lights
(not shown)
Connect
Note: This unit must be connected to 120VAC power for electronic lighting.
1. Open lid(s) or remove cover(s) from burner(s) to be lit.
2. Turn all gas control knob(s) to their OFF position(s).
3. Turn on the gas at its source.
Note: DO NOT turn on more than one valve at a time for either electronic or manual lighting.
4. Depress the desired control knob for 5 seconds, then, while pressing turn it counterclockwise
to the HI LIGHT position. Once the burner lights, release the knob.
CAUTION: If a burner does not light within fi ve (5) seconds of turning on the control
knob, depress the knob and turn it to the OFF position. WAIT FIVE (5)
MINUTES before repeating step 4. If you smell gas, follow the instructions
on the cover of the grill owner’s manual. If the burners still do not light after
several attempts, refer to the grill owner’s manual for manual lighting.
5. Repeat step 4 for each additional burner to be lit.
Fig. 5-1 - Burner valve control knob
OFF
HI
LIGHT
LOW
TO
TURN OFF
T O TURN ON
Read setting
here
HIGH to
LIGHT
To Turn OFF
To Turn ON
High to
light
Read setting here
Digital
thermometer
(if equipped)
WHEN OPERATING THIS
APPLIANCE WITH PROPANE, ALL
INSTRUCTIONS AND WARNINGS
MUST BE OBSERVED. FAILURE TO
DO SO MAY RESULT IN A FIRE OR
EXPLOSION CAUSING SERIOUS
INJURY OR DEATH.
The light switch is push button operated,
and is located on the right side of the
control panel (see Fig. 5-2). It controls the
power to all lights.
REV 1 - 1602081115
L-C2-446
E-burner
*
(pre-installed)
*
The burner ports
and carry-over slots
must be kept clean to
ensure proper ignition
and operation.
Replacement parts can
be ordered from your
local Fire Magic dealer.