Loading ...
Loading ...
Loading ...
18
31-1000600 Rev. 0
Installation Instructions - Dual Integrated Installation
FLOORING
For proper installation, this product must be placed
on a level surface of hard material that is at the same
height as the rest of the flooring. This surface should
be strong enough to support a fully loaded refrigerator
or freezer, or approximately 1,200 lbs. per unit.
NOTE: Protect the finish of the flooring.
NOTE: Not recommended for installation on carpeted
flooring.
GROUNDING THE UNIT
The power cord of this appliance is equipped with a
3-prong (grounding) plug which mates with a standard
3-prong (grounding) wall receptacle to
minimize the possibility of electric shock
hazard from this appliance.
Have the wall outlet and circuit checked
by a qualified electrician to make sure the
outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it
is your personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall outlet.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR
REMOVE THE THIRD (GROUND) PRONG
FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT
THE REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.
WARNING
Electrical Shock
Hazard. Failure to follow these instructions can
result in death, fire, or electrical shock.
STEP 1 REMOVE PACKAGING
Ŷ Remove outer carton and external packing from units.
Ŷ Inspect for damage.
Ŷ If installation will require the door
swing to be reversed, follow the
instructions in Reversing the
Door Swing section to reverse
the door swing BEFORE the unit
is removed from the shipping
skid.
Ŷ Ensure the flooring that the units
are set is clean/free of debris that could be collected
on to, or pinched in front of the wheels and damaging
the floor. Additionally, it is recommended that the
floor be protected with a plastic covering through out
the installation process.
Ŷ Remove hardware kit from top drawer.
Ŷ If installation requires a 90° door opening, the hinge
limiter pin must be installed in the top hinge BEFORE
the unit is removed from the shipping skid. Pin is
located in the hardware kit.
- Open the door approximately 45°, but no wider than
90°, to expose the hole in the back hinge bracket
and install the limiting pin. Pin must be fully seated
in the bracket or the door will not close properly.
Top
Hinge
WARNING
Tip Over Hazard. This
appliance is top heavy. Use extreme caution with
moving to prevent tipping over which could result in
death or serious injury.
KIT ZKUN PARTS SUPPLIED:
Adhesive Heater
Transformer
Front Mullion
Trim Bracket
Top Unification Bracket
Bottom Front Unification Bracket
3 1/4” Hex Head 8-18 5/8” Long Screws
5 1/4” Hex Head 8-32 5/8” Long Screws
5 3/8” Hex Head 1/4-20 1/2” Long Screws
4 wire clips
Tools and Materials Required:
1/4” and 3/8” driver / sockets
#2 Phillips screwdriver
Rubbing alcohol
AVERTISSEMENT
Risque d’électrocution
Le non-respect de ces instructions peut occasionner un
décès, un incendie ou un choc électrique
ADVERTENCIA
Riesgo de Descarga
Si no se siguen estas instrucciones, se podrá producir
la muerte, incendios o descargas eléctricas.
AVERTISSEMENT
Risque de
basculement.
Cet électroménager est lourd du haut.
Usez d’extrême prudence en le déplaçant afin de prévenir
un basculement susceptible d’occasionner des blessures
graves ou la mort.
ADVERTENCIA
Riesgo de Caída.
Este electrodoméstico es inestable. Tenga extremo
cuidado al moverlo, a fin de evitar caídas hacia adelante
que podrían resultar en la muerte o lesiones graves.
Loading ...
Loading ...
Loading ...