Loading ...
Loading ...
Loading ...
33
Sensor setting
The wash cycle sequence is optimized in Auto wash
cycles with the aid of sensors. The sensors adjust the
wash cycle strength of Auto wash cycles depending on
the amount and type of soiling. You can adjust the
sensitivity of the sensors in 3 stages.
Standard: This setting is recommend for daily regular or
typical use. This is the most energy efficient setting.
Sensitive: This setting adjusts the wash cycle strength
for the effective removal of food remnants, even if the
amount of soiling is low. The energy and water
consumption is increased accordingly.
Very sensitive: This setting adjusts the wash cycle
strength for difficult conditions of use, for example firmly
dried on food remnants. This setting is recommended if
using biological or eco detergents which contain lower
amounts of active agents. The energy and water
consumption is increased accordingly.
Extra Dry
The final rinse uses a higher temperature which improves
the drying result. The cycle time may increase slightly.
(Caution if utensils are delicate!) You can switch the Extra
Dry function on or off. There is a slight increase in energy
consumption.
Eco forecast
When Eco forecast is activated, the average water and
energy consumption of the selected wash cycle is briefly
displayed in the digital display
@.
Auto power off
This setting determines the length of time the control
panel stays illuminated after the cycle is complete.
To save energy, the recommended setting is “after one
minute”.
Possible settings are:
▯ off: The appliance does not switch off automatically.
▯ After one minute: The appliance switches off after
1 minute. This is the most energy efficient setting.
▯ After two hours: The appliance switches off after
2 hours.
Tone volume
The end of the wash cycle is indicated by a buzzer. You
can also change this setting.
Button volume
When you are operating the dishwasher, a signal sounds
whenever a button is pressed. You can control the
volume of the signal. If you do not like the button volume,
you can switch it off.
Greeting
When you switch on the dishwasher, the brand logo
appears. You can switch off the brand logo.
Factory setting
You can reset all settings to the factory setting.
Switching the appliance on
1.
Turn the water supply on fully.
2.
Open the door.
3.
Switch on On/Off switch (.
The Auto wash cycle has been preset as a default
whenever the appliance starts. This wash cycle
remains selected if no other wash cycle button
0 is
pressed.
4.
Press Start button )*.
5.
Close the door.
Wash cycle sequence starts.
Note: Your dishwasher is protected against unintentional
operation. If the appliance door remains open for more
than 4 seconds after pressing the Start button, the
operation will be paused. Press the Start button again
and close the appliance door.
Delay start time
You can delay the start of the wash cycle by up to
24 hours. Depending on the setting of the time display,
the end of cycle is indicated with “Finish in” (for example
3h 25m) or “Finish at” (for example 15:20 hours).
1.
Open the door.
2.
Switch on On/Off switch (.
3.
Select wash cycle 0.
4.
Press Delay start button `.
5.
Keep pressing the setting buttons + - X until the
displayed time corresponds with your requirements.
6.
Press Start button )*, timer programming is
activated.
7.
To delete the Delay start time, press Start button )*
for about 3 seconds.
8.
Close the door.
Note: Your dishwasher is protected against unintentional
operation. If the appliance door remains open for more
than 4 seconds after pressing the Start button, the
operation will be paused. Press the Start button again
and close the appliance door.
Sapphire Glow (emotionLight™) *
The Sapphire Glow (emotionLight™)
1" is on when the
door is open irrespective of whether the On/Off switch
( is switched on or off. When the door is closed, the
emotionLight™ is off. You can switch the EmotionLight on
or off.
Note: Note that when the door is open the
emotionLight™ is automatically switched off after 1 hour.
Loading ...
Loading ...
Loading ...