SKU NUMBER: 351-8324
Semi-flushmount
MODEL NUMBER: MND4146B
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-645-3184,
Monday - , 7:00 a.m. -4:00 p.m., CST .Friday
PACKAGE CONTENTS
1
PART
DESCRIPTION
QUANTITY
A
B
C
D
E
1pc
Finial
1pc
1pc
1pc
BB
CC
AA
Stock Part#
913759KIT
AA
BB
CC
Crossbar Assembly
Wire Connector
Outlet Box Screw
1pc
3pcs
2pcs
A
Center Stem
B
C
D
E
Socket Assembly
Shade
M1373FIVA
G13755SH
N/A
N/A
REVISED 2018-04-12
4pcs
Side Chain
M13757CHVA
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the
product.
● Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing
fuse (or switching off circuit breaker).
Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit
wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation,
which could cause serious injury or death from electric shock
WARNING:
CAUTION:
●
● All electrical connections must be in agreement with local codes, ordinances or the national electric
code (NEC). Contact your municipal building department to learn about your local codes, permits
and/or inspections.
● Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a
qualified electrician before installation.
● Do not connect this fixture to an electrical system that does not provide a means for equipment
grounding. Never use a fixture in a two-wire system that is not grounded. If you are not sure your
lighting system has a grounding means, do not attempt to install this fixture. Contact a qualified,
licensed electrician for information with regards to proper grounding methods as required by the local
electrical code in your area.
● If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct
type and electrical rating required.
Before beginning assembly, installation or operation of product, make sure all parts are present. Compare
parts with package contents list and diagram on previous page. If any part is missing or damaged, do not
attempt to assemble, install or operate the product. Contact customer service for replacement parts.
Light Source
Tools Required for Assembly (not included):
.
: (2) 100W Type-A medium base bulbs, Alternate (2) LED bulbs.
Flathead screwdriver, Phillips screwdriver, Pliers, Electrical
tape, Wire cutter, Safety glasses, ladder
PREPARATION
2
HARDWARE CONTENTS Note: Hardware not shown actual size.
Crossbar Assembly
x1
Wire Connector
x3
Outlet Box Screw
x2
AA BB CC
ASSEMBLY INSTRUCTIONS
3
Outlet Box
STEP 1:
a. Secure the crossbar (AA) to the outlet box (not
included) with outlet box screws (CC). Tighten
until snug.
The preassembled mounting screws on the
crossbar should protrude outward.
Note:
CC
AA
STEP 2:
a. Remove mounting balls from the crossbar
assembly (AA).
b. Fit the ceiling canopy to the crossbar assembly
and secure with mounting balls.
The ceiling canopy should be snug against
the ceiling and the mounting balls.
If not, adjust the length of the mounting screws on
the crossbar assembly by unscrewing the
preassembled hex nuts.
Then, screw the mounting screws in or out of the
crossbar until the desired length is achieved.
Once the ceiling canopy is secure, remove the
mounting balls and ceiling canopy and proceed to
Step 3.
Note:
?
?
?
Mounting
Screw
Hex Nut
Mounting Ball
Ceiling Canopy
WHITE
BLACK (OR RED) WIRE
WHITE OR RIBBED
BLACK OR SMOOTH
FROM SUPPLY
FROM SUPPLY
FROM FIXTURE
FROM FIXTURE
STEP 3:
* Use Wire Connectors (supplied) to connect the
wires.
ground wire green ground
screw
ground screw
ground wire supply
ground
supply white wire white
fixture supply wire
supply black (or red)
black fixture supply wire
a) Ground Wire:
1. Wrap supply around
on mounting bracket, no less than 2 in.
from the end of the wire. Tighten .
2. Connect fixture green to
wire with wire connector.
b) Supply Wire:
1. Connect the to the
with wire connector.
2. Connect the wire to the
with wire connector.
3. Wrap each connection with approved electrical
tape and carefully stuff all of the connected wires
into the outlet box.
GROUND WIRE
GROUND WIRE
FROM SUPPLY
FROM FIXTURE
GREEN GROUND SCREW
STEP 3:
a. The lanyard is provided as a means to support the
fixture from the junction box while connecting the
electrical wires. This enables the fixture to hang
from the junction box and your hands are free to
make the wire connections.
b. Turn the button stop so it may be inserted into the
crossbar slot. Make sure the button stop is
completely inside the crossbar.
c. Slowly release the fixture to make sure it is
supported by the button stop.
d. Proceed to Step 4. Once wiring is complete, the
lanyard will push into the junction box when the
Ceiling Canopy is Attached to the ceiling.
Ceiling Canopy
Slot
AA
Button Stop
Lanyard
CARE AND MAINTENANCE
TROUBLESHOOTING
1) The light does not come on at all:
2) Fuse blows or circuit trips when light is turned on.
a) Make sure the wall switch and circuit breaker are on.
b) Make sure the wiring is correct.
a) Check for crossed wires, ensure wiring is correct.
If unable to fix any of the above issues, please consult a certified electrician.
• To clean, turn off and wipe with a damp, non-abrasive cloth.
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-645-3184,
Monday - , 7:00 a.m. -4:00 p.m., CST .Friday
4
ASSEMBLY INSTRUCTIONS
STEP 6:
a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
STEP 6
Note: We recommend 2 people for this step.
a. Thread the beaded end of Center Stem (A) into
the Coupling on the underside of the Socket
Cluster. Hand tighten until snug.
b. Pass the Shade (D) over the end of the Center
Stem (A). Secure by threading the Finial (B) onto
the Center Stem (A). Hand tighten until snug.
c. One person hold the Shade (D), another person
attach the Loop on one end of the Side Chain (E)
to the Hook on the side of the Fixture Canopy of
Socket Assembly (C). Attach the Loop on the
other end of the Side Chain (E) to the Hook inside
of the Shade (D).
Coupling
A
D
B
E
C
STEP 5:
a. Re-attach the ceiling canopy of the socket
assembly (C) to the crossbar assembly (AA).
b. Secure with the previously removed mounting
balls.
Mounting
Screw
Mounting Ball
Ceiling Canopy
