Loading ...
Loading ...
Loading ...
![](https://files.manualsfile.com/34495570-bh130rn/bg12.png)
16
Note: All gas piping and connectors must conform to the Standard for Connectors for Outdoor Gas Appliances
and Manufactured Homes, ANSI Z21.75/CSA 6.27.
GAS REQUIREMENT
Verify the type of gas supply to be used, either natural or LP, and make sure the marking on the appliance rat-
ing plate agrees with that of the supply. The rating plate is located underneath the drip tray. Never connect an
unregulated gas line to the appliance. You must use the gas regulator provided with the unit, even if the supply is
controlled.
An installer-supplied gas shut-off valve must be installed in an easily accessible location. All installer supplied
parts must conform to local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA
70 or the Canadian Electrical Code, CSA C22.1, and the National Fuel Gas Code, ANSI Z223.1 or CSA B149.1 Natural
Gas Installation Code or CSA B149.2 Propane Installation Code.
All pipe sealants must be an ap proved type and resistant to the actions of LP gases. Never use pipe sealant on
flare fittings. All gas connections should be made by a qualified technician and in accordance with local codes
and ordinances. In the absence of local codes, the installation must comply with the National Fuel Gas Code,
ANSI Z223.1. Gas conversion kits are available from Customer Care. When ordering gas conversion kits, have the
model number, and the type of gas (natural or LP) from your grill.
TOTAL GAS CONSUMPTION OF THE GRILL WITH ALL BURNERS ON HI:
BH1-30R - 64,000 Btu/hr or 67.5MJ/h BGC30-BQ 50,000Btu/h or MJ/h
The appliance and its individual shut-off valve must be disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in excess of 1/2 PSIG (3.5 kPa.) The appliance must be isolat-
ed from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing
of the gas supply piping system at test pressures equal to or less than 1/2 PSIG (3.5 kPa.). The installation of this
appliance must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI
Z223.1/NFPA 54. Installation in Can ada must be in accordance with Natural Gas and Propane Installation Code,
CSA B149.1, and/or Propane Storage and Handling
Code, B149.2 and local codes.
NATURAL GAS HOOK UP: THIS TYPE OF
CONNECTION SHOULD BE PERFORMED BY A
CERTIFIED OR LICENSED TECHNICIAN ONLY.
Connection: 1/2” NPT female with 3/8” flare adapter.
Operating pressure: 4.0” W.C. 1.0kPa Supply pressure:
5” (1.2kPa) to 14” water column (2.7kPa). If in excess
of 14” W.C., a step down regulator is required. Check
with your local gas utility company or local codes for
instructions on installing gas supply lines. Be sure to
check on type and size of run, and how deep to bury
the line. If the gas line is too small, the grill will not
function properly. Any joint sealant used must be an
approved type and be resistive to the actions of LP
gases.
TO HOOKUP THE FITTINGS SUPPLIED
WITH THE GRILL:
Assemble as shown (Fig. 22). Use threading compound
on male threads only. Do not use threading compound
on the male end of the 1/2” NPT to 3/8 flare adapter.
Use a second pipe wrench to hold the grill inlet pipe to
avoid shifting any internal gas lines of the grill. Ensure that the regulator arrow points in the direction of gas flow
towards the unit, away from the supply. Do not forget to place the installer-supplied gas valve in an accessible
location.
LP GAS HOOK UP TYPE 1 OR QCC1 REGULATOR:
Grills orificed for use with LP gas come equipped with a high capacity hose/regulator assem bly for connection to
a standard 20 lb / 9kg. LP cylinder (Type 1). The LP tank is not included.
Bottom of unit
Threading compound
must be resistant to LP gas
Coupling
1/2” NPT x
2.0”
NIpple
Regulator
4.0" W.C.
Adapter 1/2” NPT
to 3/8” flare fitting
Do not put threading
compound on these
threads
*Installation must conform with local
codes or with the National Fuel Gas Code
ANSI Z223.1 or the CSA B149.2 Propane
Installation Code
Installer supplied shut-off
valve must be easily
accessible*
1/2” NPT x 5.0”
Close
Nipple
FIG. 22 Natural Gas
INSTALLATION
GAS HOOKUP
Loading ...
Loading ...
Loading ...