Loading ...
Tips for Painting with the PaintStick EZ-Twist
•
Inspect roller cover for lint before painting. If needed wash before using.
•
When using the PaintStick EZ-Twist for the first paint application, it will take most of the paint in the
PaintStick EZ-Twist tube to saturate the roller cover.
•
Keep roller moving while pushing inner handle in to prevent dripping.
•
Stop pushing inner handle in if the roller starts to skid or slide.
•
When painting in tight areas partially fill PaintStick EZ-Twist. This reduces overall length
of PaintStick EZ-Twist.
•
When leaving PaintStick EZ-Twist unattended for a longer period of time wrap roller cover in a
plastic bag.
Painting with the PaintStick EZ-Twist
1. Hold the PaintStick EZ-Twist at a 45° angle and place the fill port over the fill tube (figure A). Firmly
push down until it bottoms on the fill tube. DO NOT KEEP PaintStick EZ-Twist ON FILL TUBE FOR
LONGER THAN 1 MINUTE AT A TIME.
Note: Make sure the fill tube is opposite from where you are standing when filling
to properly seat the valve. If inner handle is difficult to pull out, hold the
black knob and twist inner handle, then pull.
2. Use your thumb to move the toggle switch into the up position. (figure B).
3. While continuing to push the PaintStick EZ-Twist securely onto fill tube with one hand, pull inner
handle back with the other hand to draw paint into handle. When the handle is full of paint, lift
PaintStick EZ-Twist slowly off fill tube while holding fill tube securely to ensure it remains in can.
(figure C).
• NOTE: If inner tube does not release from outer tube, flip toggle switch to the down position and turn
the inner tube counterclockwise to release the inner tube from the outer tube.
4. To begin applying paint, put the toggle switch in the down position. (figure D).
5. Operate the PaintStick EZ-Twist by twisting the inner tube clockwise to feed paint to the roller cover.
(figure E).
• NOTE: To use the PaintStick without the EZ-Twist feature, put the toggle switch in the up position and
push in the inner tube to feed paint to the roller cover.
• NOTE: You may also hold the clear tube and rotate the inner tube by grasping anywhere along the
outer tube.
Cleaning and Disassembling
Note: If painting with an oil based paint use manufacturer's recommended
cleaning solvent instead of warm water.
1. Return paint to container by placing PaintStick EZ-Twist on fill tube and pushing in inner handle until
stick is empty (figure F).
2. Remove paint from roller assembly by holding finger over fill port and pulling
inner handle back. Then return paint back to container (figure G).
3. Remove roller frame by unscrewing nut on end of roller frame (figure H).
4. Insert paint fill tube into PaintStick EZ-Twist fill port. Place in warm water and flush fill
tube by pulling inner handle back and pushing forward several times. Remove fill tube from PaintStick
EZ-Twist (figure I).
5. Place PaintStick EZ-Twist into clean warm water and flush fill port by plugging end of
PaintStick EZ-Twist with finger and pulling inner handle back and pushing forward several times. –
For best performance, also clean fill tube (figure J).
6a. Grasp clear tube firmly and twist handle counterclockwise to unscrew. Remove inner tube from clear
outer tube. (figure K).
• NOTE: If there is paint on the inner tube, remove it with a damp rag.
6b. To reassemble, hold the tube securely and turn the handle clockwise until secure.
• NOTE: Make sure quad rings do not get pinched or roll during assembly.
7. Remove roller from frame. Pull frame out from inner end cap until a snap is heard, or lightly tap
outside rim of end cap with hammer. Use extreme caution - do not hit metal ring on frame.
Optional Method–Use thumbs to pop off roller cover (figure L).
8. Remove inner end cap from roller cover by inserting the frame at an angle into the inner end cap
about 1". Pull gently towards you to remove cap (figure M).
9. Remove outer end cap from roller cover by inserting the frame inside the roller cover at a slightly
cocked angle. Then gently push to snap off the outer end cap with the frame. Optional method –
Remove outer end cap from roller cover using your fingers. (figure N).
Storing the PaintStick EZ-Twist
Separate inner and outer handles by quickly pulling apart (figure O).
After cleaning roller assembly components lubricate inner handle quad rings, outer end cap
fingers, and inner end cap seal with petroleum jelly. Put a small amount of petroleum jelly into the
fill port (Figure P).
PaintStick EZ-Twist Instructions
2 Y EAR
WARRANTY
GARANTÍA DE 2 AÑOS
ENGLISHPaintStick EZ-Twist
2
A
G
C
H
D E F
B
I
J K
P
NM O
L
Loading ...
Loading ...
Loading ...