Loading ...
Loading ...
Loading ...
SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION
Triggercap leaks air 1. O-ring damaged 1. Check and replace damaged O-ring (Fig, 10, No. 53
2. Valve stem, seal or O-rings damaged 2. Check and replace damaged stem, seal or O-rings
(Fig. 10, Nos. 53, 54, 55 and 58)
3ap leaks air 1. Cap bolts loose 1. Tighten bolts (Fig. 10, No. 1)
2. Damaged gasket 2. Check and replace damaged gasket (Fig. 10, No, 3)
Nose leaks air 1. Damaged cylinder O-ring 1. Check and replace damaged O-ring (Fig. 10, No. 12
2. Damaged bumper 2. Check and replace damaged bumper (Fig. 10, No. 14
3. Ram guide damaged 3. Check and replace guide (Fig. 10, No, 15)
Toolwill not operate 1. Insufficient air supply 1. Check air supply
2. Damaged or worn head valve O-ring 2. Replace damaged or worn O-ring or seal
or seal (Fig. 10, Nos. 5 and 8)
3. Damaged head valve spring 3, Replace damaged spring (Fig. t0, No. 6)
4. Head valve binding in cap 4. Clean and grease cap and head valve
(Fig. 10, Nos. 2 and 9)
Tooloperates slowly
or loses power
Tool skips fasteners or
inconsistentoperation
1. Damaged head valve spring
2. Damaged or worn O-rings
3. Damaged trigger assembly
4. Build-up on ram
5. Cylinder not sealed on bumper
properly
6. Insufficient air supply
7. Head valve poorly lubricated
1. Worn or damaged bumper
2. Build-up on ram or nose
3,
4.
5.
6.
Insufficient air supply 3.
Damaged or worn piston O-ring 4.
Damaged magazine springs 5.
Magazine-nose bolts loose 6.
7. Fasteners too short
8. Damaged fasteners
9. Incorrect fastener size
10. Cap leaks
11. Damaged trigger valve seal and
O-rings
12. Bent or damaged ram
13. Dirty magazine
14. Damaged or worn magazine
or magazine cover
1. Check and replace damaged spring (Fig. 10, No. 6)
2. Check and replace damaged or worn O-rings
3. Check and replace trigger assembly
4. Clean piston/ram assembly (Fig. t0, No. 11)
5. Disassemble cylinder and assemble properly
6. Check air supply
7. Disassemble head valve (Fig. 10, No. 9),
clean, grease, and assemble properly
1. Check and replace bumper (Fig. 10, No. 14)
2. Clean and grease piston/ram assembly (Fig. 10, No, 11)
and inside of nose cover (Fig. 10, No. 27)
Check air supply
Check and replace O-ring (Fig. 10, No. 10)
Check and replace springs (Fig. 10, No. 39)
Align nose with magazine and tighten bolts
(Fig. 10, No. 26)
7. Use Sears recommended fasteners only
8. Discard damaged fasteners
9. Use Sears recommended fasteners only
t0. Tighten cap bolts (Fig. 10, No. 1). Check and replace
damaged gasket (Fig. 10, No. 3)
11. Check and replace damaged seal and O-rings
(Fig. 10, Nos. 53, 55 and 58)
12. Check and replace damaged pistorVram assembly
(Fig. 10, No. 11)
13. Clean magazine and lubricate with a
dry, film lubricant.
14. Check and replace magazine or magazine cover
(Fig. t0, Nos. 30 and 35)
7
Loading ...
Loading ...
Loading ...