1. Home
  2. Majestic
  3. Majestic BLDV500NSCSL User Manual
  4. Page 36

Majestic BLDV500NSCSL Solitaire Series Direct Vent Natural Gas Fireplace

User Manual - Page 36

For BLDV500NSCSL.

PDF File Manual, 54 pages, Read Online | Download pdf file

BLDV500NSCSL photo
Loading ...
Loading ...
Loading ...
20306741
36
BLDV7 Series Gas Fireplace
OPERATING INSTRUCTIONS - SIGNATURE COMMAND
SYSTEM CONFIGURATION/SETUP
AllSystemconguration/setupisdoneontheCommand
Center.
NOTE: When using On/Off wall switch, the switch must be
intheONpositiontoperformallcongurationsetupsat
the command center.
COLD CLIMATE OPTION
Choose the Mode That Best Suits Your Needs
The Signature Command System is designed to operate
in either Standing Pilot or Intermittent Pilot mode.
• The Standing Pilot Mode is best for colder climates
when the pilot must remain on continuously to prevent
condensation and ensure reliable operation.
• TheIntermittentPilotModeisidealformaximumef-
ciency, igniting the pilot only when needed to start your
replace,loweringfuelconsumptionandreducingyour
carbon footprint.
Eithermodebenetsfromtheinstantaneousbatteryback-
up, so you never have to worry about a power outage.
NOTE: The Signature Command System comes standard
in the Intermittent Pilot mode, so you must follow the in-
structions below to switch to Standing Pilot Mode if needed.
Intermittent/Standing Pilot Setup (Default intermittent)
1. Holding the ON button on the Command Center while
turning on the master switch will toggle between stand-
ing pilot and intermittent pilot.
2. After the above operation, one beep (for standing pi-
lot) or two beeps (for intermittent pilot) will be given as
conrmation.
Six-hour Safety Shutdown Option (Default ON)
1. The system comes preset from the factory with a six
(6) hour shutdown from its last command of operation.
Thisisdonetopreventthereplacefromcontinuingto
operate if unattended. You may disable this feature if
you wish.
NOTE:Bydisablingthisfeature,yourreplacemaycon-
tinue to operate unattended.
Function Operation Default Setting
Intermittent/Standing Pilot
Setup
Hold the ON s button while turning on the master switch (Beep once for
standing pilot, twice for intermittent pilot)
Intermittent Pilot
Standing Pilot Temp. Shutoff Hold the ON s button 3 seconds (when the master switchon the main
burner is off)
RF Remote Receiver On/Off Push the RF receiver On/Off button on the control board (Beep once for ON
and beep twice for OFF)
RF OFF
Learn Remote Transmitter Hold the OFF t button while turning on the master switch (Beep twice then
press any handheld remote button)
6-hour Safety Shutdown setup Press the ON s button and OFF t button simultaneously (Beep once for
ON, twice for OFF)
ON
2. When the master switch is in the ON position (“-”),
pressing the ON button and the OFF button on the
Command Center simultaneously will toggle between
enabling and disabling the six-hour shutdown option.
3. After the above operation, one beep (for enabling the
six-hour shutdown option) or two beeps (for disabling the
six-hourshutdownoption)willbegivenasconrmation.
Remote Transmitter Learn Function (Default OFF)
1. The RF receiver button located on the Control Board
must be in the on position before the learn function can
begin. Use paper clip to depress button. One beep for
RF receiver ON or two beeps for RF receiver OFF will
begivenasconrmation.RefertoFigure57forlocation.
2. After the RF receiver is on, holding the OFF button on
the Command Center while turning on the master switch
will activate the learn function for the transmitter.
3. After the above operation, two beeps will be given and
thegreenLEDontheCommandCenterwillashfor
10 seconds.
4. During the 10 seconds, press the OFF button on a
transmitter to learn. Another two beeps will be given
toconrm asuccessful learning.Refer totransmitter
instructions for remote operations.
Shutting Off the Standing Pilot (Temporary Shut Off)
To shut off the standing pilot for service or summer shut
down, press and hold the ON button on the Command
Center for 3 seconds when the master switch is in the ON
position (“-”) and the main burner is off.
Note: Pilot will resume the next time system is turned on.
Key Combinations for System Settings
NOTE: When On/Off wall switch is used, it must be in the
On position to perform all system setups.
Loading ...
Loading ...
Loading ...