Indoor/Outdoor Access Point
Overview
Package Contents
Panel Layout
© 2021 TP-Link 7106509266 REV3.3.2
Power LED:
On: Power on
Off: Power off
Note: EAP225-Outdoor does not support the Remote Reset feature.
Passive PoE Adapter
Remote Reset:
Press and hold for about 8 seconds until
the LED is quickly flashing yellow then
green. The EAP will restore to factory
default settings.
LED Status
Indication
Solid green
The device is initializing or working properly.
Flashing yellow
System errors. RAM, Flash, Ethernet, WLAN or
rmware may be malfunctioning.
Flashing yellow, green
Firmware update is in progress. Do not disconnect
or power o the device.
Quickly ashing yellow, green
The device is being reset to its factory default
settings.
Flashes green twice
Initialization is completed.
SYS LED Explanation
Flashing green slowly
(Only for EAP225-Outdoor)
The device is in an isolated state.
1
Lightning and ESD Protection
Before mounting the EAP, you should consider Lightning and ESD
Protection to ensure safety.
Proper grounding is extremely important for outdoor devices. By using a
shielded CAT5e (or above) cable for connection, you can reduce the
damage of ESD attacks.
Hardware Installation
Mount the EAP
The EAP can be pole-mounted or wall-mounted. Follow the steps below
for the appropriate installation.
Option 1: Pole Mounting
Lead the end of the pole mounting strap
through the back of the EAP.
Step 1:
Position the EAP and wrap the pole
mounting strap around the pole. Feed the
end through the screw-block and tighten
the strap until the EAP is secure.
Step 2:
Option 2: Wall Mounting
Step 1:
Place the mounting bracket (for EAP) in
the right position. Mark two positions
for the screw holes .
Drill two 6 mm holes for the screws at
the marked positions.
Step 2:
Insert the plastic wall anchors into the 6
mm holes. Align the bracket (for EAP) to
the plastic wall anchors and drive the
self-tapping screws into the anchors
through the bracket (for EAP).
Step 3:
Align the mounting tabs on the back of
the EAP with the slot of the mounting
bracket (for EAP). Push and slide the
EAP downward until it locks into place.
3
Connect Cables
Firmly grasp the rear of the interface
cover and pull it downward.
Step 1:
Use an adequate Ethernet cable to
connect the LAN port. The length of
cable is up to 100 m for steady power
supply. Shielded CAT5e (or above) cable
is recommended.
Step 2:
Step 3:
Attach the waterproof rubber insert to the
groove at the underside of the device for
waterproong. Move the Ethernet cable to
the hole of the waterproof rubber insert.
Flatten the waterproof rubber insert until
it gets parallel to the device. Replace the
cover until it rmly locks into place.
Step 4:
EAP
Grounded PoE Adapter
Shielded CAT5e (or above)
Cable
Grounded 3-wire
Power Outlet
RESETShielded Ethernet
Port LAN
Passive PoE Adapter
(Mounting Bracket Included)
Power Cord
M3×28 Plastic Wall
Anchors (Qty.4)
M3×20 Self-tapping
Screws (Qty.2)
EAP
Antennas (Qty.2)
Mounting Bracket
(for EAP)
Installation Guide
Pole Mounting Strap
Waterproof Rubber
Insert
M3×16 Self-tapping
Screws (Qty.2)
45
45
Connect the antennas to the EAP. For
optimal Wi-Fi performance, adjust the
direction of the antennas. It is recom-
mended to position the antennas at
45-degree angles.
Step 3:
45
45
Step 4:
Connect the antennas to the EAP. For
optimal Wi-Fi performance, adjust the
direction of the antennas. It is recom-
mended to position the antennas at
45-degree angles.
2
Quick Installation Guide
Setup with videos
Visit https://www.tp-link.com/support/setup-video/ or scan the QR
code to search for the setup video of your product model.
Loading ...
