INSTRUCTION MANUAL
FULL SIZE ELECTRIC
CONVECTION OVEN
6400 Watts
September 2017
WARNINGS
• Do not touch any hot surfaces.
• This appliance is equipped with a three prong grounding type plug for your protection against shock hazard and should be
plugged directly into a properly grounded three prong receptacle.
• Do not immerse unit, cord or plug in liquid at any time.
• Unplug cord from outlet when not in use and before cleaning.
• Do not operate unattended.
• Do not use this unit for anything other than its intended use.
• Do not use outdoors.
• Always use on a rm, dry and level surface.
• Do not use if unit has a damaged cord or plug, in the event the appliance malfunctions, or if the appliance has been damaged in any manner.
• Keep children and animals away from unit.
• Any incorrect installation, alterations, adjustments and/or improper maintenance can lead to property loss and injury.
• All repairs should be done by authorized professionals only.
• Ensure that the designated power supply is adequate for continual usage and the voltage is correct.
• This product is a commercial machine that needs to be operated by a trained cook. Not applicable for home use.
• Do not spray water directly onto the product during cleaning. Water may conduct electricity, which may cause electric shock.
*Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death.
Read the installation, operation and maintenance instructions thoroughly before installing or servicing this equipment.
INSTALLATION
1. The appliance should be placed in a clean and at area. Do not install it directly onto the oor. Please keep a minimum
distance of 6” from non-combustible materials on each side, and 12” from non-combustible objects (e.g. walls, windows, etc.)
behind the unit.
2. Check the connection, voltage and safety grounding after installation.
3. The unit should be kept away from all ammable and explosive objects. The ambient temperature should be below 113°F
and the relative humidity should be below 85%.
4. Installation should be performed by a professional technician only.
Electric Connection:
1. The supply voltage should correspond with the working voltage of the appliance.
2. There is an earth screw at rear of the furnace body, which should be connected with a copper wire that is grounded and
complies with safety regulations.
3. The wiring should be equipped with a disconnecting switch and installed by a qualied electrician.
Water Pipe Connection:
1. Connect the solenoid valve at rear with a 1/2″ water pipe. Please connect tightly to prevent leakage.
2. Flush water into the pipe to remove the iron scale. The water hardness should be 0.5-5 (to prevent water scale)
and the pressure should be 50-200 kPa.
OPERATION
1. Before using, please check that the plug corresponds to the correct outlet being used.
2. Plug in the unit and set the timer to manual setting. Set the thermostat to 392°F to heat for 10 minutes.
(When rst using, please clean the chamber with hot water, then heat for 30 minutes at 392°F to eliminate smells from oils in
manufacturing.)
3. Open the door and put the baking trays with prepared food onto the rack inside, then close the door and set the thermostat
to the desired temperature and set the timer to the desired time. (When the food is in the oven, please make sure that
distance between the bottom of upper tray and the top of next tray is in at least 1.5” for proper hot-air circulation.)
4. If the food inside the oven is drying out, press the spray switch button during cooking to add moisture inside the chamber.
5. When the timer goes off, the unit will shut down automatically. Set the timer to manual setting, prior to cooking, to keep the
oven running continuously.
September 2017
NOTE:
The exterior of this oven gets hot during usage. To prevent injuries and burns, do not touch the appliance during operation.
For best results while baking, leave a 1.5” space between the food racks for proper air ow inside the oven chamber.
The maximum capacity for each food rack is 22 lbs.
AB EF
C
D
Control Panel
Control Panel
“A”: Timer - controls cooking and passes power.
“B”: Power indicator - displays when the timer is engaged.
“C”: Humidity - on when the spray switch is engaged.
“D”: Spray button - push down to start spraying and release to stop.
“E”: Heating - on when the unit is heating.
“F”: Temperature - controls the internal temperature, the max temperature is 572°F.
Regular Maintenance & Cleaning
• Checking the unit regularly will help prevent serious accidents from happening
• Stop using immediately if you feel that there are some problems with the unit
• Inspect the unit before each use daily
1. Before cleaning, turn off the unit and let the unit cool down completely.
2. Open the door and take out the interior racks. Clean them with water and detergent.
3. After working every day, clean the internal and external surfaces and inside chamber with a wet towel containing non-corrosive
detergent. Do not spray the machine directly with water.
4. After cleaning, put the racks back into the oven.
5. If the appliance is not going to be used for a long time, clean it and store it in a well-ventilated place without corrosive gases.
September 2017
Circuit Diagram:
If any failure occurs, please stop using and contact NSA.
1.877.672.7740
Troubleshooting
Problems Symptoms Solutions
The circuit breaker trips The electrical component leaks
Check the leakage
component, repair or replace it
Oven takes too long to heat up
1. The supply voltage is too low
2. The fan or heating element is defective
1. Replace the fuse
2. Replace the fan or
heating element
The pump has stopped
circulating
Problem with water supply or solenoid valve
1. Check water supply
2. Replace solenoid valve
September 2017
Exploded Diagram:
Rack:
28 27X14= 378
27
28
φ6和φ4
SUS304钢支
工艺
审核
1:4
共 1 张 , 第 1 张
料
版本
设计
网架660X440
D
E
F
C
1 2 3 4
B
A
321 5
C
D
4 6 7 8
A
5
B
物料编码:302110553
F
Vesta(Guangzhou)Catering Equipment Co.,Ltd.
Vesta(Guangzhou)Catering Equipment Co.,Ltd.Vesta(Guangzhou)Catering Equipment Co.,Ltd.
Vesta(Guangzhou)Catering Equipment Co.,Ltd.
7
标记
8
A
标准化
YXD-8A(Adcraft)
比例
E
处数
净重(kg)
批 准
签 名
6
日 期
更改文件号
投影
材
英联斯特(广州)餐饮设备有限公司
英联斯特(广州)餐饮设备有限公司英联斯特(广州)餐饮设备有限公司
英联斯特(广州)餐饮设备有限公司
440 ±0.50
6
660 ±0.50
4
4-R13
4
6
Adcraft订做
70
R12
46
23
黄海西 20170808
技术要求:
1、零件表面不得有刮伤，碰撞等痕迹。
2、不得有利边、毛刺、尖角等现象。
26”
17.3”
September 2017
Item No. ERP CODE DESCRIPTION QTY Remark
1 20207008015 LOWER BEAM (DOOR) 1
2 302100143 EXTERNAL DOOR GLASS 1
3 302040263 DOOR HINGE 2
4 302210697 SCREW 4 M4*10
5 20207008016 LEFT POST (DOOR) 1
6 302210712 SCREW 2 M5*8
7 302070235 HANDLE SEAT 2
8 302100144 INTERNAL DOOR GLASS 1
9 302211078 SELF-TAPPING SCREW 8 M4*8
10 301110028 THERMOSTAT KNOB 1
11 301110268 DIAL 1
12 301130015 INDICATOR 1
13 301080023 SWITCH 1
14 301130014 INDICATOR 1
15 301130013 INDICATOR 1
16 301110032 TIMER KNOB 1
17 301110005 BASE SHEET (TIMER KNOB) 1
18 302090022 RUBBER FOOT 4
19 20207008024 CONTROL PANEL 1
20 302211078 SELF-TAPPING SCREW 15 M4*8
21 301090016 A.C. CONTACTOR 2
22 301120015 TIMER 1
23 20207008023 ELECTRICAL MOUNT 1
24 301150291 FAN CONTROLLER 1
25 301010061 CAPACITOR 2
26 301050037 POWER CORD 2 meter
27 301030042 TEMP. LIMITER 1
28 301070216 PROTECTIVE RING 1
29 301100022 SOLENOID VALVE 1
30 20207008027 BEARING PLATE 2
31 301080015 TRAVEL SWITCH 1
32 302040266 HINGE HOLDER 2
33 301130038 LAMP HOLDER 2
34 301130048 LAMP 2
35 303060002 INSULATION COTTON 1.1 m2
36 20207008025 COAMING 1
37 302230002 INLET HOSE 1
38 303060002 INSULATION COTTON 1
39 302200378 WATER INLET PIPE 1
40 20207008028 BACK SHROUDING 1
41 301010204 MOTOR 2
42 BOLT 6
43 TABLETING (INLET PIPE) 2
44 20207008014 STATOR (INLET PIPE) 2
45 20107008001 CHAMBER 1
46 302020078 DOOR SEAL 1
47 302030067 TURBINE 2
48 NUT 2
49 301040230 HEATING ELEMENT 2
50 302200358 RETAINER 2
51 20107008006 ACCESS PANEL (FAN) 1
52 302110149 FAN GUARD 2
53 302110355 TRAY SHELF 2
54 301030022 THERMOSTAT 1
55 302210459 SCREW 2 M5*40
56 20207008018 TOP BEAM (DOOR) 1
57 20207008019 HANDLE 1
58 20207008017 RIGHT POST (DOOR) 1
Item No. ERP CODE DESCRIPTION QTY Remark
1 20207008015 LOWER BEAM (DOOR) 1
2 302100143 EXTERNAL DOOR GLASS 1
3 302040263 DOOR HINGE 2
4 302210697 SCREW 4 M4*10
5 20207008016 LEFT POST (DOOR) 1
6 302210712 SCREW 2 M5*8
7 302070235 HANDLE SEAT 2
8 302100144 INTERNAL DOOR GLASS 1
9 302211078 SELF-TAPPING SCREW 8 M4*8
10 301110028 THERMOSTAT KNOB 1
11 301110268 DIAL 1
12 301130015 INDICATOR 1
13 301080023 SWITCH 1
14 301130014 INDICATOR 1
15 301130013 INDICATOR 1
16 301110032 TIMER KNOB 1
17 301110005 BASE SHEET (TIMER KNOB) 1
18 302090022 RUBBER FOOT 4
19 20207008024 CONTROL PANEL 1
20 302211078 SELF-TAPPING SCREW 15 M4*8
21 301090016 A.C. CONTACTOR 2
22 301120015 TIMER 1
23 20207008023 ELECTRICAL MOUNT 1
24 301150291 FAN CONTROLLER 1
25 301010061 CAPACITOR 2
26 301050037 POWER CORD 2 meter
27 301030042 TEMP. LIMITER 1
28 301070216 PROTECTIVE RING 1
29 301100022 SOLENOID VALVE 1
30 20207008027 BEARING PLATE 2
31 301080015 TRAVEL SWITCH 1
32 302040266 HINGE HOLDER 2
33 301130038 LAMP HOLDER 2
34 301130048 LAMP 2
35 303060002 INSULATION COTTON 1.1 m2
36 20207008025 COAMING 1
37 302230002 INLET HOSE 1
38 303060002 INSULATION COTTON 1
39 302200378 WATER INLET PIPE 1
40 20207008028 BACK SHROUDING 1
41 301010204 MOTOR 2
42 BOLT 6
43 TABLETING (INLET PIPE) 2
44 20207008014 STATOR (INLET PIPE) 2
45 20107008001 CHAMBER 1
46 302020078 DOOR SEAL 1
47 302030067 TURBINE 2
48 NUT 2
49 301040230 HEATING ELEMENT 2
50 302200358 RETAINER 2
51 20107008006 ACCESS PANEL (FAN) 1
52 302110149 FAN GUARD 2
53 302110355 TRAY SHELF 2
54 301030022 THERMOSTAT 1
55 302210459 SCREW 2 M5*40
56 20207008018 TOP BEAM (DOOR) 1
57 20207008019 HANDLE 1
58 20207008017 RIGHT POST (DOOR) 1
Parts List:
59
4
RACK
September 2017
=
=
ACE
Equipment
One Year Limited
Warranty
ACE warrants its equipment against defects in materials and workmanship, subject to the following conditions:
ACE Equipment is warranted for one year, effective from the date of purchase by the original owner. A copy of the
original receipt or other proof of purchase is required to obtain warranty coverage. This warranty applies to the original
owner only, and is not assignable.
Should any product fail to function in its intended manner under normal use within the limits defined in this
warranty, at ACE’s discretion, such product will be repaired, replaced with a refurbished unit, or replaced with a new
unit by ACE, after defective unit has been inspected and defect has been confirmed. ACE does not assume any liability
for extended delays in replacing any item beyond its control. This warranty does not apply to rubber and non-metallic
synthetic parts that may need to be replaced due to normal usage, wear or lack of preventative maintenance.
This warranty covers products shipped into the 48 contiguous United States, Hawaii, and metropolitan areas of Alaska
and Canada. Warranty coverage on products used outside the 48 contiguous United States, Hawaii and metropolitan
areas of Alaska and Canada may vary.
The following conditions are not covered by warranty:
•
Equipment failure relating to improper installation, improper utility connection or supply and problems due to
improper ventilation.
•
Equipment that has not properly been maintained, damage from improper cleaning, and water damage
to controls.
•
Equipment that has not been used in an appropriate manner, or has been subject to misuse, neglect, abuse,
accident, alteration, negligence, damage during transit, delivery or installation, fire, flood, riot, or act of God.
•
Equipment that has the model number or serial number removed or altered.
•
Equipment on which the security seal has been broken.
If the equipment has been changed, altered, modified, or repaired without express written permission from ACE, then the
manufacturer shall not be liable for any damages to any person or to any property, which may result from the use of this
equipment thereafter.
This equipment is intended for commercial use only and this warranty is void if equipment is used in other than a
commercial application.
For warranty and non-warranty related issues, technical support, please contact NSA at 1-877-672-7740. To
purchase replacement parts and warranty registration visit www.admiralcraft.com. Please have your model
number, serial number
and proof of purchase ready. It is not necessary to contact the place where you originally
purchased your product from.
“THE FOREGOING WARRANTY IS IN LIEU OF ANY AND ALL WARRANTIES EXPRESSED OR IMPLIED
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILTY OR FITNESS FOR PARTICULAR
PURPOSES AND CONSTITUTES THE ENTIRE LIABILITY OF ACE. IN NO EVENT DOES THE
LIMITED WARRANTY EXTEND BEYOND THE TERMS STATED HEREIN.”
VERSION 09.17
