Oliveri SS2525-GM Essente Goose Neck Pull Out Mixer Tap Gunmetal

Installation Instruction

For SS2525-GM. Additionally, the document applies to other Oliveri models: SS2525, SS2575

PDF File Manual, 4 pages, Read Online | Download pdf file

SS2525-GM photo
background
Before attempting any work involving mains water supply lines, ensure the water supply is shut off.
Stop valves (preferably with filters) must be used when installing your Oliveri mixer to allow isolation. (not
supplied with mixer). Failure to do so where required will void warranty.
This mixer tap is already pre-assembled and tested. Do not disassemble, as this may void the warranty.
This mixer tap must be installed in accordance with these instructions.
Essente stainless steel goose neck pull out mixer
SS2525
Where water pressure exceeds 500kPa, a pressure reducing device is required to be installed. Note that
water pressure overnight can reach 150% of the daytime pressure.
CARE & MAINTENANCE
Unscrew and clean the spout aerator periodically - especially if you notice a drop in water pressure.
The polished chrome plate finish on your Oliveri mixer tap will resist stains and dirt build up.
Clean with a soft cloth and warm soapy water as necessary - rinse and dry after cleaning. Avoid using abrasive
or acid based cleaning products.
WARRANTY
This mixer tap is warranted to be free from manufacturing defects for a period of 10 Years: 5 years only (parts
& labour) plus an additional 5 years on the Cartridge (parts only), when used in a domestic situation.
This warranty does not cover against normal wear and will be voided if the product is misused or not
installed in accordance with these instructions. Note: Fitting spout-attached devices, including water filters,
to this mixer will void warranty.
In the event this product is rendered obsolete and a replacement product is required, Tasman Sinkware
reserves the right to supply a product of equal substitution at their discretion.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
SERVICE
If the problem represents a danger, or damage to property may occur, immediately shut off the water supply.
If the mixer tap requires servicing, please contact your plumber (preferably the one who installed it).
Most problems occur due to contaminated supply lines or water pressure exceeding 500kPa.
If the Plumber is satisfied that the problem is not due to poor installation, contact T2 Services Pty Ltd for
assistance on:
Ph: (07) 5596 0738
Fax: (07) 5527 3353
If a warranty service call finds that the mixer tap is not at fault, T2 Services Pty Ltd reserves the right to pass
on any callout fee to the householder.
THIS MIXER TAP MUST BE INSTALLED BY A LICENSED PLUMBER IN
ACCORDANCE WITH LOCAL REGULATIONS
This Oliveri tap is manufactured to standard AS/NZS 3718.
Note: Installation of aerators containing flow regulators.
Upon re-installation, the aerator should be tightened with an aerator key to prevent removal by hand.
Note: Ceramic Cartidges - Warranty claims will not be honoured where the ceramic cartridge has
malfunctioned due the the presence in the water supply of;
- Copper tube pieces, sand, dirt or stones
- Thread tape
- Other objects not normally present in potable water supplies.
- Do not remove the cartridge from the body as it has been pressure tested and tightened to a
specific torque.
Technical Data
Installation Instructions
TF 182b - SS2525 installation instructions.pdf
MAX OPERATING PRESSURE: ..............................................................5 bar (500kPa)
RECOMMENDED OPERATION PRESSURE: ..........................................1.5-5 bar (150-500kPa)
MAX HOT WATER TEMPERATURE: .....................................................65°C
RECOMMENDED HOT WATER TEMPERATURE: ..................................50°C
Loading page 2...
Loading page 3...
Loading page 4...

Other documents for Oliveri SS2525-GM

The following documents are available:
Installation Instruction Specification
  • SS2525-GM - Oliveri - Specifications Sheet - (English) Download
Photos

Specifications

Installation Instruction - Transcript

  • Page 1 - English - : Before attempting any work involving mains water supply lines ensure the water supply is shut off Stop valves preferably with filters must be used when installing your Oliveri mixer to allow isolation not supplied with mixer Failure to do so where required will void warranty This mixer tap is already preassembled and tested Do not disassemble as this may void the warranty This mixer tap must be installed in accordance with these instructions Essente stainless steel goose neck pull out mixer SS2525 Where water pressure exceeds 500kPa a pressure reducing device is required to be installed Note that water pressure overnight can reach 150 of the daytime pressure CARE amp MAINTENANCE Unscrew and clean the spout aerator periodically especially if you notice a drop in water pressure The polished chrome plate finish on your Oliveri mixer tap will resist stains and dirt build up Clean with a soft cloth and warm soapy water as necessary rinse and dry after cleaning Avoid using abrasive or acid based cleaning products WARRANTY This mixer tap is warranted to be free from manufacturing defects for a period of 10 Years 5 years only parts amp labour plus an additional 5 years on the Cartridge parts only when used in a domestic situation This warranty does not cover against normal wear and will be voided if the product is misused or not installed in accordance with these instructions Note Fitting spoutattached devices including water filters to this mixer will void warranty In the event this product is rendered obsolete and a replacement product is required Tasman Sinkware reserves the right to supply a product of equal substitution at their discretion Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure SERVICE If the problem represents a danger or damage to property may occur immediately shut off the water supply If the mixer tap requires servicing please contact your plumber preferably the one who installed it Most problems occur due to contaminated supply lines or water pressure exceeding 500kPa If the Plumber is satisfied that the problem is not due to poor installation contact T2 Services Pty Ltd for assistance on Ph 07 5596 0738 Fax 07 5527 3353 Email oliverit2servicescomau If a warranty service call finds that the mixer tap is not at fault T2 Services Pty Ltd reserves the right to pass on any callout fee to the householder THIS MIXER TAP MUST BE INSTALLED BY A LICENSED PLUMBER IN ACCORDANCE WITH LOCAL REGULATIONS This Oliveri tap is manufactured to standard ASNZS 3718 Note Installation of aerators containing flow regulators Upon reinstallation the aerator should be tightened with an aerator key to prevent removal by hand Note Ceramic Cartidges Warranty claims will not be honoured where the ceramic cartridge has malfunctioned due the the presence in the water supply of Copper tube pieces sand dirt or stones Thread tape Other objects not normally present in potable water supplies Do not remove the cartridge from the body as it has been pressure tested and tightened to a specific torque Technical Data Installation Instructions TF 182b SS2525 installation instructionspdf MAX OPERATING PRESSURE 5 bar 500kPa RECOMMENDED OPERATION PRESSURE 155 bar 150500kPa MAX HOT WATER TEMPERATURE 65C RECOMMENDED HOT WATER TEMPERATURE 50C
  • Page 2 - English - : Installation Instructions Installation Instructions SS2525 SS2575 General Note This product is to be installed by a licensed plumber installation must comply with ASNZS 3500 and local plumbing codes Pressures amp Temperatures Maximum Hydrostatic Pressure 500 kpa As per ASNZS3500 Note ASNZS 350012003 Clause 334 states that Provision shall be made to ensure that the maximum static pressure at any outlet other than a fire service outlet within a building does not exceed 500 kPa Note Pressures above 500kPa can cause damage from water hammer reduced life of appliances taps and fittings and cause excessive noise in the system Minimum Hydrostatic Pressure 100 kpa The Maximum operating temperature for the Mixer Tap is 65 o C Please ensure that the lines are flushed prior to installation as contaminates in the water can damage the Ceramic Cartridge flow regulator and also affect the performance of the Mixer NB This mixer is designed to have the Handle to the right hand side of the mixer doing so will put the cold inlet to the front of the mixer the purpose is to assist with accidental scalding if a child pulls the handle forward trying to turn on the mixer installing the handle to the centre will put the cold on the left hand side which is not recommended 1 Remove product from packaging and check for damages if the product is damaged do not install and return to store of purchase 2 The WELS compliant aerator has been preassembled into the mixer outlet To comply with WELS the flow regulated aerator must remain in place 3 Ensure Product is complete as per exploded drawing 4 A single 35mm Hole is required in the mounting surface 5 The maximum mounting surface thickness cannot exceed 37mm 6 Fit Oring A to bottom of mixer body 7 Screw the Mixer tails B into base of the Mixer being careful to avoid damage to the oring seals 8 Feed Male end of braided hose H through top of mounting surface NB Hose Adaptor J amp Washer I are lightly screwed to male end of Hose H this fitting will need to removed for ease of feeding hose through mounting surface 9 Feed the Mixer tails B through the mounting surface each Tail alternatively 10 The Mixer inlet ports are colour coded Red for hot and Blue for cold 11 Position the mixer on the mounting surface ensuring the sealing washer A is positioned correctly 12 Feed Mixer tails each alternatively through Stabiliser Plate C 13 Slide Rubber Washer D onto Mixer thread followed by Metal Washer E 14 Using Fixing Nut F tighten Mixer to mounting Surface lock Fixing nut in place with screws G 15 Screw Hose adaptor J to Male threaded end of hose H ensuring sealing washer I is in place 16 Screw hose adaptor J to Mixer Water Outlet port being careful to avoid damage to the oring seals 17 Connect Mixer tails B to Mains Water supply line 18 NB Ensure the Mixer tails are not Kinked Bent stretched or twisted when assembling to the Mains Water Supply The Mixer Tail connection between the mixer and the Water supply must have a natural curve Ensure Mixer tails are not exposed to Abrasions corrosive agents or alike 19 It is recommended that InLine filters be installed to ensure a cleaner flow of water to the mixer 20 The Braided hose will have a natural curve under the mounting surface on the hand piece side of the curve fit the Return Weight K using the two screws provided Fit the weight approximately 100mm up from the bottom of the curve the position can be adjusted to suit but the weight must remain on the hand piece side of the curve To the consumer 1 The Mixer is to only be cleaned with warm soapy water 2 Under No Circumstances should any abrasive cream or acid based cleaning agents be used as these types of cleaners will damage the chrome finish Cartridge seals and aerators TF 182b SS2525 installation instructionspdf A C D E F G J I H B Max 37 K
  • Page 3 - English - : Installation Instructions Installation Instructions SS2525 SS2575 General Note This product is to be installed by a licensed plumber installation must comply with ASNZS 3500 and local plumbing codes Pressures amp Temperatures Maximum Hydrostatic Pressure 500 kpa As per ASNZS3500 Note ASNZS 350012003 Clause 334 states that Provision shall be made to ensure that the maximum static pressure at any outlet other than a fire service outlet within a building does not exceed 500 kPa Note Pressures above 500kPa can cause damage from water hammer reduced life of appliances taps and fittings and cause excessive noise in the system Minimum Hydrostatic Pressure 100 kpa The Maximum operating temperature for the Mixer Tap is 65 o C Please ensure that the lines are flushed prior to installation as contaminates in the water can damage the Ceramic Cartridge flow regulator and also affect the performance of the Mixer NB This mixer is designed to have the Handle to the right hand side of the mixer doing so will put the cold inlet to the front of the mixer the purpose is to assist with accidental scalding if a child pulls the handle forward trying to turn on the mixer installing the handle to the centre will put the cold on the left hand side which is not recommended 1 Remove product from packaging and check for damages if the product is damaged do not install and return to store of purchase 2 The WELS compliant aerator has been preassembled into the mixer outlet To comply with WELS the flow regulated aerator must remain in place 3 Ensure Product is complete as per exploded drawing 4 A single 35mm Hole is required in the mounting surface 5 The maximum mounting surface thickness cannot exceed 37mm 6 Fit Oring A to bottom of mixer body 7 Screw the Mixer tails B into base of the Mixer being careful to avoid damage to the oring seals 8 Feed Male end of braided hose H through top of mounting surface NB Hose Adaptor J amp Washer I are lightly screwed to male end of Hose H this fitting will need to removed for ease of feeding hose through mounting surface 9 Feed the Mixer tails B through the mounting surface each Tail alternatively 10 The Mixer inlet ports are colour coded Red for hot and Blue for cold 11 Position the mixer on the mounting surface ensuring the sealing washer A is positioned correctly 12 Feed Mixer tails each alternatively through Stabiliser Plate C 13 Slide Rubber Washer D onto Mixer thread followed by Metal Washer E 14 Using Fixing Nut F tighten Mixer to mounting Surface lock Fixing nut in place with screws G 15 Screw Hose adaptor J to Male threaded end of hose H ensuring sealing washer I is in place 16 Screw hose adaptor J to Mixer Water Outlet port being careful to avoid damage to the oring seals 17 Connect Mixer tails B to Mains Water supply line 18 NB Ensure the Mixer tails are not Kinked Bent stretched or twisted when assembling to the Mains Water Supply The Mixer Tail connection between the mixer and the Water supply must have a natural curve Ensure Mixer tails are not exposed to Abrasions corrosive agents or alike 19 It is recommended that InLine filters be installed to ensure a cleaner flow of water to the mixer 20 The Braided hose will have a natural curve under the mounting surface on the hand piece side of the curve fit the Return Weight K using the two screws provided Fit the weight approximately 100mm up from the bottom of the curve the position can be adjusted to suit but the weight must remain on the hand piece side of the curve To the consumer 1 The Mixer is to only be cleaned with warm soapy water 2 Under No Circumstances should any abrasive cream or acid based cleaning agents be used as these types of cleaners will damage the chrome finish Cartridge seals and aerators TF 182b SS2525 installation instructionspdf A C D E F G J I H B Max 37 K
  • Page 4 - English - : Before attempting any work involving mains water supply lines ensure the water supply is shut off Stop valves preferably with filters must be used when installing your Oliveri mixer to allow isolation not supplied with mixer Failure to do so where required will void warranty This mixer tap is already preassembled and tested Do not disassemble as this may void the warranty This mixer tap must be installed in accordance with these instructions Essente stainless steel goose neck pull out mixer SS2525 Where water pressure exceeds 500kPa a pressure reducing device is required to be installed Note that water pressure overnight can reach 150 of the daytime pressure CARE amp MAINTENANCE Unscrew and clean the spout aerator periodically especially if you notice a drop in water pressure The polished chrome plate finish on your Oliveri mixer tap will resist stains and dirt build up Clean with a soft cloth and warm soapy water as necessary rinse and dry after cleaning Avoid using abrasive or acid based cleaning products WARRANTY This mixer tap is warranted to be free from manufacturing defects for a period of 10 Years 5 years only parts amp labour plus an additional 5 years on the Cartridge parts only when used in a domestic situation This warranty does not cover against normal wear and will be voided if the product is misused or not installed in accordance with these instructions Note Fitting spoutattached devices including water filters to this mixer will void warranty In the event this product is rendered obsolete and a replacement product is required Tasman Sinkware reserves the right to supply a product of equal substitution at their discretion Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure SERVICE If the problem represents a danger or damage to property may occur immediately shut off the water supply If the mixer tap requires servicing please contact your plumber preferably the one who installed it Most problems occur due to contaminated supply lines or water pressure exceeding 500kPa If the Plumber is satisfied that the problem is not due to poor installation contact T2 Services Pty Ltd for assistance on Ph 07 5596 0738 Fax 07 5527 3353 Email oliverit2servicescomau If a warranty service call finds that the mixer tap is not at fault T2 Services Pty Ltd reserves the right to pass on any callout fee to the householder THIS MIXER TAP MUST BE INSTALLED BY A LICENSED PLUMBER IN ACCORDANCE WITH LOCAL REGULATIONS This Oliveri tap is manufactured to standard ASNZS 3718 Note Installation of aerators containing flow regulators Upon reinstallation the aerator should be tightened with an aerator key to prevent removal by hand Note Ceramic Cartidges Warranty claims will not be honoured where the ceramic cartridge has malfunctioned due the the presence in the water supply of Copper tube pieces sand dirt or stones Thread tape Other objects not normally present in potable water supplies Do not remove the cartridge from the body as it has been pressure tested and tightened to a specific torque Technical Data Installation Instructions TF 182b SS2525 installation instructionspdf MAX OPERATING PRESSURE 5 bar 500kPa RECOMMENDED OPERATION PRESSURE 155 bar 150500kPa MAX HOT WATER TEMPERATURE 65C RECOMMENDED HOT WATER TEMPERATURE 50C