Loading ...
Loading ...
Loading ...
18
WASHER CARE (cont.)
c. Close the washer door and the dispenser drawer.
d. Do not add any detergent or other chemicals to the
washer when following this procedure.
e. Select the Clean Washer with affresh
®
cycle.
f. On some models: Select the FanFresh
®
option
to help dry the washer interior after the cycle is
complete.
NOTE: The washer remembers your last option
selection and will use it for future wash cycles until
you deselect that option.
g. Touch and hold START/PAUSE to begin the cycle.
The Clean Washer with affresh
®
cycle operation
is described below.
NOTE: For best results, do not interrupt cycle.
Description of Clean Washer with affresh
®
Cycle
Operation:
1. The Clean Washer with affresh
®
cycle will determine
whether clothing or other items are in the washer.
2. If no items are detected in the washer, it will proceed with
the cycle.
a. If any items are detected in the washer, “rL”
(remove load) will be displayed. The door will unlock.
Open washer and remove any garments from the
washer drum.
b. Touch POWER to clear the “rL” code.
c. Touch and hold START/PAUSE to restart the cycle.
3. Steam models only: During the rst 20 minutes of the
cycle, it will activate the steamer but the drum will not
spin or ll with water. You may see condensation on the
door window during this initial phase. If you are using
an affresh
®
Washer Cleaner tablet, it will not dissolve
completely during the steam phase. This is normal.
After the cycle is complete, leave the door open slightly to
allow for better ventilation and drying of the washer interior.
Cleaning the Dispensers
After using the Clean Washer with affresh
®
cycle, you may
nd some residue buildup in the washer’s dispensers.
To remove residue from the single load dispenser, remove
the drawer and wipe the surfaces with an affresh
®
Machine
Cleaning Wipe or a damp cloth and towel dry either before
or after you run the Clean Washer with affresh
®
cycle. Use
an all-purpose surface cleaner, if needed.
On some models: To remove residue from the Load & Go™
bulk dispenser, lift the handle on the dispenser housing and
pull to remove it from the washer cabinet; then rinse the
dispenser thoroughly with running water. Wipe the outside
dispenser surface with an affresh
®
Machine Cleaning Wipe
or a damp cloth, and towel dry. Use an all-purpose surface
cleaner, if needed.
Replace the dispenser in the washer cabinet and make sure
that it is correctly seated.
IMPORTANT: Dispensers are not dishwasher-safe.
Cleaning the Outside of the Washer
Use an affresh
®
Machine Cleaning Wipe or a soft, damp
cloth or sponge to wipe up any spills. Occasionally wipe the
outside of your washer to help keep it looking new. Use an
affresh
®
Machine Cleaning Wipe or mild soap and water.
IMPORTANT: To avoid damaging the washer’s nish, do not
use abrasive products.
CLEAN WASHER CYCLE REMINDER
NOTE: Not all models have the Clean Washer with affresh
®
cycle reminder light.
The Clean Washer with affresh
®
LED will ash at the end of a
wash cycle when the washer has run 30 wash cycles. This is
a reminder to run the Clean Washer with affresh
®
cycle.
If the Clean Washer with affresh
®
cycle is not turned on, the
LED will stop ashing at the end of a wash cycle after running
three more regular wash cycles. After 30 more wash cycles
are completed, the Clean Washer with affresh
®
LED will again
ash at the end of a wash cycle as a reminder.
REMOVING THE DISPENSER (cont.)
Removing the Dispenser
To remove:
1. Pull dispenser drawer out until it stops.
2. Press down on the release tab and pull straight out
to remove the dispenser.
3. Lift off cover panel
by pulling straight up.
To replace:
1. Position cover panel back
onto posts on dispenser.
Apply slight pressure on
cover panel to seat it.
2. Align edges of dispenser
with guides in washer;
then slide dispenser
back into slot.
Single Load Dispenser Drawer
Loading ...
Loading ...
Loading ...