Loading ...
Loading ...
Loading ...
- 6 -
03/2021
Copyright © 2021, Fast ČR, a.s.
Attention:
Do not use the steam function for silk and synthetics so as not to
damage the fabric.
WATER SPRAYING FUNCTION
■ The water spraying function can be used with any ironing method. It serves to
moisten the fabric and effectively helps with ironing heavily crumpled textiles.
■ Make sure that there is asufficient amount of water in the water tank and turn the
iron so that its front side points towards the location that you wish to spray.
■ Press the water spraying button
. Water will spray out of the nozzle on the front
side.
Note:
When using the water spraying function for the first time or when you
have not used the iron for along time, it will be necessary to press the
water spraying button several times before the nozzle starts working
correctly.
DRIP-STOP SYSTEM
■ The iron is equipped with the Drip-Stop system, which automatically stops water
supply when the set temperature is insufficient for generating steam and thereby
prevents potential dripping of hot water out of the steam outlets.
ANTI-CALC SYSTEM
■ This iron is equipped with apermanent Anti- Calc filter, which limits the formation of
limescale deposits inside the iron. This filter cannot be deactivated. The effectiveness
of the filter depends on the hardness of the water used.
AUTOMATIC SHUT-OFF FUNCTION
■ If you leave the iron motionless for 8 minutes in the vertical position or 30 seconds
in the horizontal position or tipped on its side, the iron will turn off automatically.
Attention:
Despite the iron being equipped with an automatic shut off
function, for safety reasons, never leave it without supervision,
when it is connecting to a mains power socket.
■ In the event that the iron has automatically shut itself down, simply lift it up or move
it substantially. The heating indicator will be lit and the iron will again be ready for
use.
TURNING OFF
■ Stand the iron upright and set the steam release regulator to position .
■ Set the temperature control knob to the MIN position.
■ Disconnect the power cord from the power socket and allow the soleplate to
cool down. After the soleplate has cooled down, clean the iron according to the
instructions in chapter Cleaning and maintenance.
TIPS FOR QUALITY IRONING
■ If you are ironing fabrics from blended materials (e.g. 40% wool and 60% synthetic
material), set the temperature according to the material which is ironed at alower
temperature.
■ If you do not know the composition of the fabric, identify the suitable temperature
setting by ironing apiece of the fabric from the underside. Start by setting alow
temperature and gradually increase it until the ideal temperatures is achieved.
■ Never iron over places that have sweat marks or other stains. The high temperature
fixes the stain in place, making it difficult to remove.
■ To avoid silk, wool and synthetic fabrics from being shiny after ironing, iron them
from the underside.
■ Some materials are easier to iron when they are lightly damp.
■ Spray fine fabrics before ironing them or iron them under a lightly dampened
wiping cloth.
CLEANING AND MAINTENANCE
CLEANING AFTER EVERY USE
Attention:
Before cleaning, the iron must be disconnected from the power
socket and cooled down.
Do not submerge the iron in water when cleaning it.
■ Open the water tank cap and empty out the remaining contents of the water tank
over asink. Close the cap.
■ In the event that the soleplate or the surface of the iron is dirty, wipe with alightly
dampened cloth and then wipe dry.
■ For cleaning, do not use steel wool, solvents or cleaning products with an abrasive
effect, etc. to prevent damaging the surface being cleaned.
REMOVING LIMESCALE DEPOSITS
■ For the removal of limescale deposits from the inner part of the soleplate, the iron
is equipped with aself cleaning function. Use this function regularly at least once
every 14 days.
■ Fill the water tank with clean water up to the maximum water level mark. Connect
the iron to a power socket and set the temperature control knob to the MAX
position. Wait until the heating indicator turns off. Then disconnect the iron from
the power supply again.
■ Hold the iron in ahorizontal position above the sink. Set the steam release regulator
to the Self Clean position. Steam and hot water will start to be released from the
soleplate. At the same time also limescale deposits from the inner parts of the
soleplate will be removed. Tilt the iron from side to side several times until the water
tank is completely emptied out. After emptying it out, slide the regulator to position
. You may repeat this process once more if necessary.
■ Connect the iron to a power socket and allow it to heat up once more to the
maximum temperature in order to dry out the soleplate. Iron over a piece of
unneeded fabric to remove any water stains that may have formed on the soleplate
during the cleaning process. Unplug the iron from the power socket and allow it
to cool down.
STORAGE
■ After you have finished ironing, pour out any unused water from the water tank
(careful, it may be hot), or allow it to evaporate if necessary and allow the iron to cool
down. Set the steam release regulator to position
. Wind the power cord around
the stand, making sure that the power cord is not touching the soleplate, and stand
the iron on the stand A10.
Attention:
Keep the stored iron away from extreme temperatures, direct
sunlight and excessive humidity and do not store it in an overly
dusty environment. Do not place anything on to the stored iron.
TECHNICAL SPECIFICATIONS
Rated voltage range .................................................................................................... 220−240 VAC
Rated frequency ......................................................................................................................50-60 Hz
Rated power input ....................................................................................................... 2,000-2,400 W
Continuous steam output .................................................................................................... 30 g/min
Steam impulse ........................................................................................................................120 g/min
Water tank capacity ................................................................................................................... 260 ml
Dimensions (length × width × height) .................................. 286 mm × 122 mm × 139 mm
Weight ........................................................................................................................................... 1 050 g
Changes to text and technical parameters are reserved.
INSTRUCTIONS AND INFORMATION REGARDING THE
DISPOSAL OF USED PACKAGING MATERIALS
Dispose of used packaging material at asite designated for waste in your municipality.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC
EQUIPMENT
This symbol on products or original documents means that used
electric or electronic products must not be added to ordinary
municipal waste. For proper disposal, renewal and recycling, hand
over these appliances to determined collection points. Alternatively,
in some European Union states or other European countries you may
return your appliances to the local retailer when buying an equivalent
new appliance.
Correct disposal of this product helps save valuable natural resources
and prevents potential negative effects on the environment and human health, which
could result from improper waste disposal. Ask your local authorities or collection
facility for more details.
In accordance with national regulations penalties may be imposed for the incorrect
disposal of this type of waste.
For business entities in European Union states
If you want to dispose of electric or electronic equipment, ask your retailer or supplier
for the necessary information.
Disposal in other countries outside the European Union.
This symbol is valid in the European Union. If you wish to dispose of this product,
request the necessary information about the correct disposal method from the local
council or from your retailer.
This product meets all the basic requirements of EU directives related to
it.