Loading ...
Loading ...
Loading ...
Doe het volgende voordat u uw kooktop gaat gebruiken:
• Verwijder al het verpakkingsmateriaal
• Zet het toestel op een droge, vlakke, harde, stabiele en onbrandbare ondergrond
• Houd het toestel uit de buurt van andere warmtebronnen en zorg dat er aan de
voor- en achterkant en de zijkanten minstens 5 cm vrij is voor luchtcirculatie.
Voor uw veiligheid mag u nooit de elektrische (massa) aansluiting uit de stekker
snijden, verwijderen of uitschakelen. Gebruik nooit een aangepaste stekker of een
verlengsnoer met de kooktop.
MANUAL TRANSLATION ADDENDUM
DUTCH
87
Symptom Possible Cause Possible Solution
No power (no
lights or fan
noise.)
• Unit unplugged.
• No power to
receptacle.
• Plug unit into appropriate
receptacle.
• Make sure that receptacle is
energized.
• Check wall switches.
• Check circuit breaker.
• Plug a different electronic device
into the receptacle to make sure
that power is present.
Pan does not
heat.
• Pan is not induction
efcient.
• Pan not centered.
• Use induction efcient pan.
• Center pan.
4- or 6-hob unit
suddenly stops
heating.
• Possible power brown
out.
• Circuit shared with
another electrical
device.
• Safety shut-off
engaged.
• Assure proper voltage/power levels.
• Make sure the stock pot heater is
not sharing a circuit with electrical
devices.
• The safety shut-off will engage if an
empty pan is left on the 4- or 6-hob
unit while the unit is working at full
power. Make sure that the unit’s
surface is clear. Wait 15-20 minutes
for the unit to reset.
Pan does not
get hot enough
even though
power levels are
set to maximum
– induction
efcient pan in
use.
• Extension cord in use.
• Circuit shared with
another electrical
device.
• DO NOT use extension cords.
Extension cords may affect
the power levels reaching the
appliance.
• Make sure that the 4- or 6-hob unit
is not sharing a circuit with other
electrical devices.
Pan heats
unevenly, does
not maintain
heat level, or
overheats.
• Pan is not induction
efcient.
• Pan bottom may not
be at enough.
• Pan not centered.
• Use induction efcient pan.
• Use atter pan.
• Center pan.
TROUBLESHOOTING
In the event of a possible malfunction, your CookTek 4- or 6-hob unit will ash an
error code on the LED display. Please consult the following table when encountering
an error code. To reset error conditions, remove the pan from the unit and turn the
power knob to the vertical off position, or unplug the unit.
Error Error Cause Display Troubleshooting
1 Broken Temperature
Sensor.
E-01 Service required.
2 Incompatible pan. E-02 Try different induction-efcient
pan.
3 Over current (peak). E-03 Try different induction-efcient
pan. Service may be required.
4 Overheat. E-04 Turn the unit off. Let unit cool for
15 minutes. Keep surrounding air
temperature below 115°F/46°C.
6 High line voltage. E-06 To reset, unplug unit, wait 5
seconds, and plug in again.
If problem persists, have an
electrician monitor the line
voltage.
7 Hardware failure. E-07 Service required.
8 Zero cross failure. E-08 Turn unit off, then on. Plug unit
into outlet on different circuit
breaker. If problem persists, have
an electrician monitor the line
voltage.
9 Hardware failure. E-09 Service required.
ERROR CODES
Loading ...
Loading ...
Loading ...