Loading ...
Loading ...
Loading ...
10
Basic charger should be cleaned with a
damp cloth only (picture
5
).
Accessories
(depending on model)
Smartphone Holder
• Before each use, make sure mirror, suc-
tion cup surface (11d) and holding bra-
ckets (11a) are always clean and dry (pic-
ture B1). Use a fuzz-free cloth for cleaning
suction cup surface and mirror. In particu-
lar make sure suction cup surface and
mirror are free from any contamination
(e.g. hair, dust, oil, fuzz, dirt etc.).
• Press your smartphone holder (11) just with
enough pressure, centered at nose level on
a sturdy mirror. Then mount the holder by
pressing the lever arm (11b) towards the
mirror until it snaps in (picture B2).
Note: Only affix on mirror to ensure safe
and correct conditions. For use in ba-
throom only. Do not use in automobiles.
• Always make sure the smartphone holder
is securely mounted on the mirror before
inserting your smartphone. Place your
smartphone (portrait) sideways in bet-
ween the holding brackets (11a) by pres-
sing against one bracket with your phone
and sliding the other bracket to the side
(picture B2). Follow the same procedure
to remove your phone again.
• Adjust the overall position for the required
angle by moving the ball joint of the holder
(picture B3).
• Once done, remove your phone from the
holder. Take off the smartphone holder by
flipping the lever arm back and pulling the
tab carefully (picture B4 1./2.). Affix
smartphone holder with each use again.
• The smartphone holder should be cleaned
with a damp fuzz-free cloth only (picture
5
). You may use glass cleaner, alcohol or
similar products (avoid products with sili-
cone oil). Make sure the surface is dry and
dust free after cleaning. Store in clean and
dry place. If not in use, always remove
your smartphone from the holder.
Note: Smartphone width required for
usage: minimum 58mm, maximum 83mm.
Caution: Small parts may come off, keep
out of reach of children.
• Follow your smartphone’s user manual to
ensure your phone/charger is designed for
use in a bathroom environment.
Charging Travel Case
• To charge your handle (5) place it on the
pin in the charging travel case (12) and
connect it to an electric outlet, using the
extra smart plug (13) provided.
• The flashing light (12a) of the charging
travel case indicates that the handle is
charging. Once the handle is fully charged
the light turns off. A full charge takes typi-
cally 12 hours (picture D1).
Note: You may use the USB port (12b) to
charge an electric device while the charg-
ing travel case is plugged in. The handle
can only be charged with the smart plug
(13)/(12c) not via USB port.
• The inner lid of the travel case has a
built-in smartphone holder (12d), which
can hold your smartphone while using
(picture D2). Before use, make sure your
phone fits the stand and keeps stable.
• The removable inlay (12e) of the travel
case is dishwasher-safe (picture
5
).
The outer case should be cleaned with
a damp cloth only. Make sure that travel
case parts are completely dry before reas-
sembling and toothbrush/brush heads are
dry before storing in the travel case.
Note: Clean stains on travel case surface
immediately. Store travel case in a clean and
dry place.
Follow your smartphone’s user manual to
ensure your phone/charger is designed for
use in a bathroom environment.
Beauty Bag
Store your clean and dry toothbrush/brush
heads in the travel case (15) and place it
inside the beauty bag (14) (picture E1/2).
Clean stains on the surface immediately.
The beauty bag should be hand washed only
with lukewarm water (30 °C – 40 °C) (picture
5). Store in clean and dry place.
Subject to change without notice.
Environmental Notice
Product contains batteries and/or
recyclable electric waste. For
environment protection do not
dispose in household waste, but
for recycling take to electric waste collection
points provided in your country.
Loading ...
Loading ...
Loading ...