User Manual Lokithor JA300 Jump Starter with Air Compressor

• User Manual - (English, German, Chinese)

• Safety Information - (English)

• Specification Sheet - (English)

Table of contents

• Product Overview
• Main operartion interface and screen
• Operating Procedure
• Troubleshooting

Product Overview

Main operartion interface and screen

2.Description

Operating Procedure

1. How to power up the jump starter?

Press the "Light"or "Power" button

2. How to use the jump-start function?

Method one: Normal start

1. Connect the jump starter clamps with the EC8 connector to the jump starter.
2. Connect the red (+) clamp to the positive (+) terminal on the vehicle battery and the black (-) clamp to the negative (-) terminal on the vehicle battery, and make sure that the connections are good.
3. Press the "Lighf'or "Power" button to power on the product. The green light on the screen will light up and flash if there are no issues. At this time, you'll be able to start your vehicle.
4. If the vehicle starts successfully, the jump starter will automatically disable the power output.
5. In most cases, the vehicle will be able to start immediately after the jump starter has been connected. Some vehicles may need to be connected to the jump starter for 30~120 seconds (the product will charge the car battery at this time) to continue the operation. If the vehicle does not start immediately, Please wait 20-30 seconds before each attempt. Do not attempt more than five times within ISminutes.
6. Please remove the jump-start clamps from the car battery instantly after you finished the starting. Pressing on the "Power" button for 2 seconds to shut down jump starter. If there are no operations for 60 seconds, the product will automatically shut down.

Method two: Forced start

1. At this time, the normal start mode fails to start, e.g: the voltage of the car battery is very low (the voltage is less than IV),you can use the forced emergency start function after checking the operating specifications in the manual;
2. Connect the jump starter clamps to the EC8 connector on the Jump-Starter;
3. When the jump starter is on, tapping and holding on the "BAR/PSI" button for 5 seconds will enter the forced start mode. At this time, the green light on the screen is always lighting, which means that the output of the ignition clips are normally turned on. At this time, you must prevent the positive and negative poles from being short-circuited; (In this mode, it is required to turn on the forced start function first, and then connect the ignition clips to the car battery, otherwise the output cannot be turned on);
4. Connect the red (+) clamp to the positive (+) terminal on the vehicle battery and the black (-) clamp to the negative (-) terminal on the vehicle battery(during the connection process, there will be a slight sparking phenomenon, which is normal) and make sure that the connections are good; At this time, the overall voltage of the jump starter connected in parallel with the vehicle is displaying on the screen, then you can jump-starting the vehicle;
5. Shortly press the "Power"or "BAR/PSI"button to exit.

3. How to use voltmeter function

1. Connect the jump starter clamps to the EC8 connector on the Jump-Starter;
2. Connect the red (+) clamp to the positive (+) terminal on the vehicle battery and the black (-) clamp to the negative (-) terminal on the vehicle battery, and make sure that the connections are good;
3. At this time, the green light on the main interface flashes, and the overall positive and negative voltages of the starting power supply connected in parallel with the car are displayed at the same time, and it enters the starting mode. To check only the voltage of the car battery, short press the "ON" button to exit the starting mode and enter the measurement Mode, the "green light" goes out, the display only displays the voltage value of the car battery, so as to determine whether the battery is damaged;
4. Disconnect the alligator clamps from the vehicle battery and exit the voltmeter function mode.
   

4. How to use the air inflator function?

1. The inflatable hose is connected to the output port of the air inflator, and then tighten the nut, and the other end is connected to the car tire;
2. To wake the product (short press the "Light" button or short press the "Switch" button) to enter the air inflator mode;
3. Short press the "BAR/PSI" button to switch the pressure unit of tire pressure: BAR, PSI;

4. To set the target tire pressure value, you must first know the tire pressure requirements of the tire. (For the standard tire pressure value of the tire, you can check the pressure value mark on the tire, or check the manual of the inflated product), set the target tire pressure value by pressing "+ . After setting, the value will flash for 3 seconds, exit the setting state and enter the real-time monitoring state of tire pressure

5. Long Press the "PUMP" button for 3 seconds to turn on the air inflator. When the tire pressure reaches the set value, the air inflator will be turned off automatically. To turn off the inflator manually: press the "PUMP" button or the "Switch" button;

6. Remove the inflatable hose.

5.How to use LED light?

• Long press the "Light" button for one second, the LED lights up;
• Short press the "Light" button in order to switch the modes of ON, Strobe, SOS and OFF;
• Long press the "Light" button for two seconds to turn off the LED light forcefully.

6. How to charge your jump starter

1. You will need the following: USB power adapter(5V output USB power adapter or 9V2A USB power adapter if QC protocol supported) and a USB To Type-C cable.
2. Plug the USB plug/A Port into the power adapter and the C port into the jump starter's charging port. At this point, the battery indicator and the "In" icon on the screen will turn on, indicating that the product is charging.
3. In the case of running out of power or low power, please charge the product in time to prevent battery under-voltage. Long-term no power status of battery may cause the product to fail to charge.

7. How to use the 5V USB-A port to charge your mobile phone

1. You will need the following: USB To USB-C cable and a mobile phone (if the mobile phone supports 9V2A of QC protocol, it can support 9V2A fast charge);
2. When the "USB" icon on the screen light up, plug the USB plug/A Port to the jump starter and the C port into your mobile device.

Troubleshooting