Sirius SLT958EM User Manual

Loading ...

Remove the grease lter by pulling its han-

dle.

To reinsert the grease lter after the cleaning,

just perform the opposite operation.

Attention: after refastening the stainless steel

panel make sure that it is properly xed.

Tocleantheapplianceitself tepid water and

neutral detergents are recommended, while

abrasive products must be avoided.

For steel appliances specialized detergen-

ts are recommended (please follow the in-

structions mentioned on the product itself to

obtain the desired results).

To replace the lamp, (SLT950 EM- SLT951

EM , SLT950.1, SLT953 ) remove the lamp

(Fig. 9) and replace it with a lamp of the same

kind.

To replace the uorescent lamps (SLT952

and SLT952EM) you need to disconnect the

appliance from the electrical network, then

open the panel following the instructions gi-

ven in the ‘USES’ section.

Remove the perimeter screws shown in g.

14; pull the uorescent lamps support out

(g.15), and replace the old lamp with a new

one of the same kind.

Ret the panel and the screws previously re-

moved.

To replace the uorescent lamps ballast plea-

se follow the steps described above.

If the panels of the hood SLT952 are out of

line and not perfectly at, it is possible to re-

gulate the screws xing the panel, in order to

align them and make them at again.

After you have opened the panels, according

to the preceding instructions, unscrew the

screw you can see on picture 18 and lift up

or down the panel in order to align it with the

other and make them perfectly at.

Tighten the screw you had loosen and close

the panel.

SubstitutionoftheLEDbar:

Using an appropriate tool, remove the LED

bar from its seat (refer to Fig. 19), disconnect

it electronically using the appropriate con-

nector then substitute it with a LED bar with

same characteristics.

If the client increases or reduces the speed

while the timer is on, this is automatically

stopped.

Standardconguration

If two cookerhoods-radiocontrol system are

installed in the same room or in the immediate

vicinity, each system may aect the operation

of the other, due to the fact that they have the

same code. Therefore it will be necessary to

change the code of one of the radio controls.

Warning:

The battery should be replaced eve-

ry yearto guarantee theoptimal rangeof

thetransmitter. Toreplacethe exhausted

battery,taketheplasticlido,removethe

batteryandreplaceitwithanewone,ob-

servingthecorrectbatterypolarities.Used

batteries should be discarded in special

collectionbins.

Generatinganewtransmissioncode

The radiocontrol is supplied by the manufac-

turer with default codes stored. If you want to

create a new set of codes, proceed as follows:

press and hold the UP, STOP and DOWN but-

tons simultaneously for 2 seconds. Afterthe

LEDS light up, press the UP and DOWN button

swithin 5 seconds. The LEDS will ash 3 times

to indicate that the process is completed.

WARNING: This procedure deletes all pre-

viously stored codes.

Learningthenewtransmissioncode

After changing the transmission code on the

radio control, the cooker hood electronic con-

trol unit must be made to set the new code

as follows: press the main Power O button

on the cookerhood (g. 8) and then restore

power to the electronic control unit. Within

the next 15 seconds, press the Light button.

This will ensure the control unit is synchroni-

zed with the new code.

MAINTENANCE

An accurate maintenance guarantees good

functioning and long-lasting performance.

A special care must be paid with grease l-

ters: to remove the grease lter please follow

the instructions given in the ‘USES’ section ,

according to the model chosen.

Loading ...

Sirius SLT958EM 90cm Valentina Ceiling Cassette Rangehood

User Manual - Page 16