Canarm EFT896432TD Fluorescent Tandem Strip Light

User Manual

For EFT896432TD.

PDF File Manual, 1 pages, Download pdf file

1. Remove the metal cover by
loosening the screw.
2. Locate the 2 pre-wired
sockets from inside the housing.
Remove the metal plate by
loosening the screw. Push the
sockets so that they snap into the
slots on the top plate. Re-attach
the metal plate to the housing by
tightening the screw.
3. Turn the fixture over and
locate the center knockout. Make
sure the fixture is supported on
the underside and break part of
the knockout away using a
hammer and screw driver. Twist
out the knockout using pliers.
4. Position the housing on the
ceiling with the center knockout
over the electrical box. Mark the
ceiling for the pilot hole locations
through the small holes on either
end. Drill 1/8” pilot holes at each
location. Determine the
appropriate way of fastening the
fixture to the ceiling (wood screws
or toggle bolts, not included).
Note: Toggle bolts will require a
larger pilot hole. Secure the
fixture to the ceiling using the
appropriate fasteners.
5. Connect the ground wire to
the ground screw located near the
center knockout. Connect the
black wire from the fixture to the
black wire from the electrical box.
Connect the white wire from the
fixture to the white wire from the
electrical box. Once wires are
connected, carefully tuck wires
and marretts into the metal outlet
box.
6. Alternatively, if an outlet
(electrical) box is not available,
if the fixture doesn’t cover the
outlet (electrical) box entirely or
if the electrical leads are coming
from either end of the fixture,
please consult a qualified
electrician for Armour Cable or
Conduit Electrical Feed type of
installation.
7. Re-attach the metal cover to
the housing. Slide the end with
the 2 tabs into the 2 holes at the
end of the fixture and position the
wire cover onto the fixture.
Secure in place using the same
screw removed earlier.
8. Install proper bulb type and
wattage. Insert the pins on both
ends of the fluorescent tube into
the lamp holders on both ends.
Rotate the tube until a slight
"click" is felt. Repeat for additional
bulbs.
washer
washer
housing
ceiling
housing
ceiling
joist
toggle bolt
Imported By: CANARM LTD., 2555 Rue Bernard Lefebvre, Laval Quebec H7C 0A5, PH: (450) 665-2535, FX: (450) 665-0910
INSTALLATION: NOTE: Product May Not Look Exactly As Shown In Figures.
centre knockout
holes
electrical
box
white
wire
black
wire
ground wire
ground
screw
centre
knockout
Wood Screw
Toggle Bolt
extending
tabs
extending
tab holes
hole
screw
end knockout
armour cable or conduit
electrical feed
Consult a qualified electrician
metal plate
sockets
screw
housing
top plate
FL-13ES
02/11
FLUORESCENT
LIGHTING
Star-headed
Screwdriver
Wiring supplies
as required by
electrical code
Pliers
Hammer
QUESTIONS OR CONCERNS, CONTACT CANARM AT:
1-800-265-1833 (English) 1-800-567-2513 (French) Monday through Friday 8:00 AM to 5:00 PM E.S.T.
TOOLS AND MATERIALS REQUIRED:
L
I
G
H
T
I
N
G
&
F
A
N
S
E
C
L
A
I
R
A
G
E
S
&
V
E
N
T
I
L
A
T
E
U
R
S
!
INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS
READ ALL INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS
SAVE THESE INSTRUCTIONS
SAFETY PRECAUTIONS:
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS
INVOLVED.
3. THIS FIXTURE IS DESIGNED FOR 120 VOLT CIRCUIT. IF UNSURE ABOUT WIRING, CONSULT AN ELECTRICIAN.
WARNING: DO NOT CONNECT FIXTURE TO DIMMER CIRCUIT.
4. THIS FIXTURE MUST BE GROUNDED PROPERLY. CONNECT THE GROUND WIRE (BARE COPPER OR GREEN) TO
THE AC SUPPLY GROUND WIRE (BARE COPPER OR GREEN) OR GROUND SCREW IN THE ELECTRICAL OUTLET
BOX. IF GROUND WIRE IS NOT AVAILABLE IN YOUR AC SUPPLY WIRE SYSTEM, PLEASE CONSULT A QUALIFIED
ELECTRICIAN BEFORE PROCEEDING THE ELECTRICAL CONNECTION.
5. USE ONLY ENERGY STAR APPROVED BALLAST (WITH LAMP SOCKETS) MANUFACTURED BY CSA FILE
NUMBER 226237 AND MARKETED BY CANARM LIMITED. THIS BALLAST IS REPLACEABLE BY A
QUALIFIED ELECTRICIAN WITHOUT CUTTING OF THE WIRES.
9. When the ballast is replaced, reverse the process from step 8 to
5. Loosen the screw and nut to remove the ballast and sockets
from fixture. After that repeat the normal process from step 5 to 8.