Loading ...
Loading ...
Loading ...
English
10
Adjusting Mower Height (Fig. H)
The height of cut is adjusted by the cut height adjust
lever
10
.
Mulching (Fig.G)
DANGER: Turn unit off and remove safety key and
batterypacks.
1. To operate mower in mulching mode, remove the grass
collection bag
12
.
2. Be sure rear door cover
11
isclosed.
Grass Collection Bag (Fig.G)
DANGER: Turn unit off and remove safety key and
batterypacks.
1. To attach, lift the rear door cover
11
and place the grass
collection bag
12
onto the mower so the bag hooks on
frame
16
slide into the bag pins on mower
17
. Then,
lower the rear door cover onto thebag.
2. To remove, lift the rear door cover and pull the grass
collection bag off of the mower by unhooking it off the
bag pins. Then, lower the rear door cover so it fully covers
the backopening.
Adjusting Handle Height (Fig.F)
The mower is shipped in storage mode. You will need to
adjust the handle to operating position beforecontinuing.
1. To unlock the handle
4
from the storage position, twist
the two handle lock knobs
6
a quarter turn. The handle
lock knobs are located on both sides of the handle.
2. Raise the handle to the operatingposition. Take care to
not pinch or stress thecord.
3. Twist the handle lock knobs a quarter turn, securing the
handle intoposition.
Assembling the Grass Collection Bag (Fig. E)
WARNING: Under normal usage, the collection
bag assembly is subject to deterioration and
wear and should, therefore, be frequently
checked for replacement. Any replacement
assembly should be checked for compliance with
CRAFTSMANrecommendations.
1. Before starting to assemble the grass collection bag
12
to the frame
16
, check that the grass bag and frame are
similar to Fig.E.
2. Slide the frame into the bag, ensuring the bag handle
13
remains outside the bag.
3. Assemble the top clips to the frame, then assemble the
two side clips and the bottom cliplast.
ASSEMBLY AND ADJUSTMENTS
DANGER: To reduce the risk of serious personal
injury, turn unit off and remove the safety key and
battery packs before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can causeinjury.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Wall Mounting
Some CRAFTSMAN chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1” (25.4mm) long, with a screw head
diameter of 0.28–0.35” (7–9mm), screwed into wood to an
optimal depth leaving approximately 7/32” (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in theslots.
nOTE: Do not attempt to mount CMCB101 charger under a
bench ortable.
nOTE: Only mount CMCB101 charger with the charging
lights pointed upward toward theceiling.
VersaTrack™
WARNING: Do not charge batteries while charger is
hung onTrackwall.
CRAFTSMAN chargers, except the CMCB101, can be
stored on CRAFTSMAN VersaTrack™ Trackwall. Hooks and
accessories are sold separately. Please refer to the VersaTrack™
Trackwall accessory sheet for furtherinformation.
nOTE: The CMCB101 charger is not CRAFTSMAN VersaTrack™
Trackwallcompatible.
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65°F – 75°F (18°C – 24°C);
d. If charging problems persist, take the tool, battery
pack and charger to your local servicecenter.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse effect on the batterypack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles should
be kept away from charger cavities. Always unplug the
charger from the power supply when there is no battery
pack in the cavity. Unplug the charger before attempting
toclean.
6. Do not freeze or immerse the charger in water or any
otherliquid.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaningsolutions.
Loading ...
Loading ...
Loading ...