Loading ...
Loading ...
Loading ...
s ' A Ice ....
Depending on your model, you may have one or more of the
following options: the ability to select either crushed or cubed
ice, a special light that turns on when you use the dispenser, or a
lock option to avoid unintentional dispensing.
NOTES:
• The dispensing system will not operate when the freezer door
is open.
• After connecting the refrigerator to a water source, flush the
water system. Use a sturdy container to depress and hold the
water dispenser pad for 5 seconds, then release it for
5 seconds. Repeat until water begins to flow. Once water
begins to flow, continue depressing and releasing the
dispenser pad (5 seconds on, 5 seconds off) for an additional
5 minutes. This will flush air from the filter and water
dispensing system. Additional flushing may be required in
some households. As air is cleared from the system, water
may spurt out of the dispenser.
• Allow 24 hours for the refrigerator to cool down and chill
water.
Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
The display screen on the dispenser control panel has a
backlight, which will turn off automatically when the control
buttons have not been used for 30 seconds or more. When
the backlight is off, the first press of a control button will only
reactivate the backlight, without changing any settings. Within
30 seconds after the backlight has been reactivated,
additional presses of control buttons will change the
applicable settings.
The Water Dispenser
IMPORTANT: Dispense enough water every week to maintain a
fresh supply.
Water Dispenser Buttons and Pad
There are three dispenser panel buttons primarily used in the
water dispensing process:
• In the row of six buttons below the dispenser display screen,
the fourth button (from the left) is the WATER selection
button. It is used to select water instead of ice for dispensing.
• Centered below the row of six buttons is the WATER
dispenser button. This is used to actually dispense water.
• In the row of six buttons, the fifth button (from the left) is the
MEASURE FILL button. This activates the Measured Fill
feature.
light Itemperature
AB C
A. WATERselection button
B. WATERdispenser button
C. MEASURE FILL button
The dispenser pad is located on the back wall of the dispenser
cavity. When pressed, either water or ice will dispense,
depending on the chosen setting.
To Dispense Water (Standard):
1. To select water, press the WATER selection button. The
display screen will indicate when water is selected.
y water
2. Press a sturdy glass against the dispenser pad OR place the
glass below the water dispenser and press the WATER
dispenser button.
3. Remove the glass OR release the button to stop dispensing.
NOTE: While dispensing water and for 5 seconds after
dispensing has stopped, the digital display will show how
much water has been dispensed.
To Dispense Water (Measured Fill):
Measured Fill allows you to dispense a specified amount of water
with the touch of a few buttons.
NOTE: The amount of water you select will be dispensed. Be
sure that the container is empty and can hold the entire volume. If
ice is in the container, you may need to adjust your selection.
1. Press MEASURE FILL to turn the feature on. The Measured
Fill options will appear on the display screen.
El
unit home
2.
3.
4=
5=
At any time while Measured Fill is active, press HOME to turn
off the feature.
NOTE: The dispenser will automatically turn off Measured Fill
after 15 seconds of inactivity.
You can dispense water by the ounce, cup, or liter. Press
UNIT to select your desired setting. Default, minimum, and
maximum volumes are listed below.
Units Default Minimum Maximum
Ounces 8 1 128
Cups 1 1/4 16
Liters 0.25 0.05 4
Press the "+" and "-" buttons to adjust the volume as desired.
NOTE: Most coffee cups (commonly 4 to 6 oz [118 to
177 mL] per cup) are not the same size as a measuring cup
(8 oz [237 mL]). You may need to adjust the volume to avoid
unintentionally overfilling coffee cups.
To dispense water, press and hold a sturdy glass against the
dispenser pad OR place the glass below the dispenser and
press and release the WATER dispenser button.
NOTE: While dispensing water, the digital display will count
down how much water remains to be dispensed, according
to the volume you selected. The flow of water will
automatically stop once the desired volume has been
dispensed.
To stop dispensing before the entire selected volume has
been dispensed, remove the glass from the dispenser pad
OR press and release the WATER dispenser button a second
time.
NOTE: To select a new volume or select the same volume
again, you must first finish dispensing the selected volume, or
turn off the Measured Fill feature and then turn it back on.
Loading ...
Loading ...
Loading ...